1. Introdución
This manual provides comprehensive instructions for the safe and effective operation of your DeFelsko PosiTector 6000 F1 Coating Thickness Gauge. This instrument is designed for accurate measurement of coating thickness on ferrous metal substrates. Please read this manual thoroughly before using the device to ensure proper handling and to maximize its lifespan.
2. Información de seguridade
Always observe the following safety precautions to prevent injury or damage to the instrument:
- Do not expose the gauge to extreme temperatures, humidity, or corrosive environments.
- Avoid dropping the instrument or subjecting it to severe impact.
- Do not attempt to disassemble or repair the gauge yourself. Refer all servicing to qualified personnel.
- Keep the probe tip clean and free from debris to ensure accurate readings.
- Empregue só o tipo de pila especificado (AAA) e asegúrese de manter a polaridade correcta durante a instalación.
3. Contido do paquete
Verify that all items listed below are present in your DeFelsko PosiTector 6000 F1 package:
- DeFelsko PosiTector 6000 F1 Coating Thickness Gauge with Built-in Probe
- Maletín de transporte
- Precision Plastic Shims
- Protective Lens Shield
- Protective Rubber Holster
- Correa de pulso
- Pilas AAA (3 incluídas)
- NIST Calibration Certificate
4. Produto rematadoview
The DeFelsko PosiTector 6000 F1 is a robust and accurate instrument designed for measuring coating thickness. Below are key components of the gauge:
Figura 4.1: Fronte view of the DeFelsko PosiTector 6000 F1 showing the display, control buttons, and integrated probe.
- Visualización: Digital screen showing measurement readings, units, and menu options.
- Botóns de control: Used for navigation, calibration, and setting adjustments.
- Integrated Probe: The sensor at the bottom of the unit used to contact the coated surface for measurement.
- Compartimento de batería: Located at the rear, for AAA batteries.
5. Configuración
5.1 Instalación da batería
- Locate the battery compartment cover on the back of the gauge.
- Deslice a tapa para abrir.
- Insert three (3) AAA batteries, ensuring correct polarity as indicated inside the compartment.
- Pecha a tapa do compartimento da batería de forma segura.
5.2 Encendido inicial
Press the power button (usually the center button) to turn on the gauge. The display will illuminate and show the current measurement mode.
5.3 Attaching Wrist Strap and Holster
For added security and protection, attach the included wrist strap to the designated loop on the gauge and place the gauge into the protective rubber holster.
6. Instrucións de funcionamento
6.1 Medición básica
- Ensure the gauge is powered on.
- Place the probe flat on the coated surface to be measured. Ensure full contact.
- The reading will appear instantly on the display.
- Lift the probe from the surface to take another measurement.
Figure 6.1: The PosiTector 6000 F1 being used to measure coating thickness on a metal I-beam.
Figure 6.2: The PosiTector 6000 F1 being used to measure coating thickness on a curved pipe surface.
6.2 Calibración
Regular calibration ensures the accuracy of your gauge. Refer to the detailed calibration procedure in the full PosiTector 6000 manual for specific steps using the included precision plastic shims and uncoated ferrous metal substrate.
6.3 Selección da unidade
The PosiTector 6000 F1 can display measurements in mils (thou) or micrometers (um). Consult the gauge's menu system (typically accessed via the center button) to switch between these units as needed.
7. Mantemento
7.1 Limpeza
- Wipe the gauge body with a soft, dry cloth.
- For the probe tip, use a soft cloth lightly dampened with isopropyl alcohol if necessary. Ensure no liquid enters the gauge.
- Non use produtos de limpeza ou disolventes abrasivos.
7.2 Almacenamento
When not in use, store the PosiTector 6000 F1 in its protective carrying case in a dry, temperature-controlled environment. Remove batteries if storing for extended periods to prevent leakage.
8 Solución de problemas
| Problema | Causa posible | Solución |
|---|---|---|
| O manómetro non se acende. | Baterías gastadas ou instaladas incorrectamente. | Substitúa as pilas por pilas AAA novas, asegurándose de manter a polaridade correcta. |
| Lecturas inexactas. | Probe tip dirty; improper calibration; surface not flat. | Clean probe tip; perform calibration; ensure probe is flat on surface. |
| Display shows "---". | No contact with ferrous substrate; measurement out of range. | Ensure probe is on a ferrous metal; check if coating thickness exceeds gauge's range. |
If the problem persists after attempting these solutions, please contact DeFelsko customer support.
9. Especificacións
- Maximum Thickness Measured: 60 mil (1500 um)
- Minimum Thickness Measured: 0 mil
- Thickness Measurement Accuracy: +(0.05 mil + 1 Percent) Up to 2 mil; +(0.1 mil + 1 Percent) greater than 2 mils
- Calibration Certificate Type: NIST
- Tipo de visualización: Dixital
- Number of Records Stored: 1,000
- Método de proba: Magnético
- Material compatible: Metal ferroso
- Fonte de enerxía: 3 pilas AAA (incluídas)
- Dimensións do produto: 9 x 5 x 3 polgadas
- Peso do artigo: 1 libra
- Número de modelo: F1
- ASIN: B0052P4B7G
- Fabricante: Defelsko
10. Garantía e soporte
DeFelsko products are known for their quality and reliability. For detailed warranty information and technical support, please refer to the official DeFelsko website or contact their customer service department directly. Keep your purchase receipt and the NIST Calibration Certificate for warranty claims.
Información de contacto: Por favor visite www.defelsko.com para obter os recursos de asistencia e os datos de contacto máis recentes.