Lutron Maestro MS-OPS2-WH Motion Sensor Light Switch Instruction Manual

1. Introdución

The Lutron Maestro Motion Sensor Light Switch (model MS-OPS2-WH) is designed to automatically control lighting based on occupancy and ambient light levels. This single-pole switch offers convenience and energy savings by turning lights on when a room is entered and off when it is vacated. It is compatible with various bulb types, including CFL, LED, incandescent, halogen, and electronic low voltage.

2. Precaucións de seguridade

AVISO: Risk of Electric Shock. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before installing or servicing this device. Consult a qualified electrician if you are unsure about any part of the installation process. Use this device with copper or copper-clad wire only.

• Apague o interruptor de circuito antes da instalación.
• Asegúrese de que todas as conexións de cableado estean seguras.
• Non o instale se o produto parece estar danado.
• Só para uso en interiores.

3. Contido do paquete

• 1x Lutron Maestro MS-OPS2-WH Motion Sensor Switch
• Wiring hardware (wire nuts, screws)
• Folla de instrucións

Note: A coordinating wall plate is sold separately.

4. Especificacións

5. Configuración e instalación

Installation typically takes around 15 minutes. Follow these steps carefully:

1. Apagar a enerxía: Locate the circuit breaker or fuse box that controls the light switch you are replacing. Turn off the power to that circuit. Verify the power is off using a voltagprobador.
2. Eliminar o interruptor existente: Retira con coidado a placa de parede e desenrosca o interruptor existente da caixa de parede. Desconecta os cables do interruptor antigo.
3. Conecta o interruptor Maestro: The Maestro switch requires a ground wire connection. If no neutral wire is present in your wall box, the switch can be installed using the ground wire. Connect the wires as follows:
   • Conecta o cable de terra verde from the Maestro switch to the bare copper or green ground wire in the wall box.
   • Conecta o fío negro from the Maestro switch to the incoming hot wire in the wall box.
   • Conecta o remaining black wire from the Maestro switch to the load wire (going to the light fixture).
   • Se a cable neutro (typically white) is present in your wall box, connect the blue wire from the Maestro switch to the neutral bundle. If no neutral is present, cap off the blue wire.

   

   

4. Montar o interruptor: Carefully push the wired switch into the wall box. Secure it with the provided screws.
5. Instalar placa de parede: Attach a compatible decorator-style wall plate (sold separately) over the switch.
6. Restaurar enerxía: Volve a conectar o interruptor.

6. Instrucións de funcionamento

6.1. Control manual

Preme o grande Toca Cambiar button (top part of the switch) to manually turn the lights ON or OFF. The sensor will resume automatic operation after a manual override.

6.2. Modos de funcionamento

The Maestro switch supports multiple operating modes. To change modes, remove the wall plate to access the small programming button on the side of the switch. Press and hold the programming button until the indicator light flashes to cycle through modes.

• Modo de ocupación (activación automática, desactivación automática): Lights turn on automatically when motion is detected and turn off automatically after the room is vacated and the set timeout period expires. This is the default mode.
• Modo de vacancia (activación manual, desactivación automática): Lights must be turned on manually by pressing the Tap Switch. They will turn off automatically after the room is vacated and the set timeout period expires.
• Detección de luz diurna: The sensor measures ambient light. If sufficient natural light is present, the lights will not turn on automatically, even if motion is detected. This feature helps save energy by preventing lights from turning on unnecessarily.

6.3. Adjusting Timeout Settings

The switch can be programmed to turn off lights after 1, 5, 15, or 30 minutes of no occupancy. To adjust this setting, press and hold the large Tap Switch button until the indicator light flashes a specific number of times corresponding to the desired timeout:

• 1 flash: 1 minute timeout
• 2 flashes: 5 minute timeout
• 3 flashes: 15 minute timeout
• 4 flashes: 30 minute timeout

6.4. Adjusting Motion Sensitivity

The motion sensor's sensitivity can be adjusted. To do this, simultaneously press and hold both the large Tap Switch button and the small programming button on the side of the switch. The indicator light will flash to confirm the change between high and low sensitivity settings.

7. Mantemento

Para limpar o interruptor, limpe cun pano suave eamp cloth. Do not use abrasive cleaners or solvents. Ensure the sensor lens is clear of dust and obstructions for optimal performance.

8 Solución de problemas

• As luces non se acenden:
  • Comprobe se o disxuntor está activado.
  • Asegúrese de que todas as conexións de cableado estean seguras.
  • Verify the operating mode is set to Occupancy (Auto ON).
  • Check if Daylight Sensing is active and there is sufficient ambient light.
• Lights turn off too quickly/slowly:
  • Adjust the timeout setting as described in Section 6.3.
  • Ensure the sensor is not obstructed and has a clear view da sala.
• Lights turn on unexpectedly:
  • Adjust the motion sensitivity as described in Section 6.4.
  • Ensure the sensor is not detecting motion from outside the intended area.

9. Garantía e soporte

The Lutron Maestro Motion Sensor Light Switch comes with a 10-year warranty upon product registration. A 5-year warranty is provided without registration. For technical assistance or further information, please refer to the official Lutron support channels.