1. Información de seguridade
This Kidde Pi9010 Dual Sensor Smoke Alarm is designed to provide early warning of fire. For optimal protection, it combines both ionization and photoelectric sensing technologies to detect both fast-flaming and slow-smoldering fires.
- Importante: Lea todas as instrucións antes da instalación e o funcionamento.
- Colocación: Install smoke alarms on every floor of your home, inside each bedroom, and outside sleeping areas.
- Proba: Test the alarm weekly to ensure proper function.
- Listado UL: This dual-sensor smoke alarm is UL listed, ensuring compliance with safety standards.
2. Produto rematadoview
The Kidde Pi9010 is a battery-operated smoke alarm featuring dual sensing technology for comprehensive fire detection. It includes a Hush feature to temporarily silence nuisance alarms and a test/reset button for easy verification of operation.
Características principais:
- Dual Photoelectric and Ionization Sensors
- 9-Volt Battery Powered (battery included)
- Hush Feature for Nuisance Alarms
- Botón Test/Reset
- Red LED Indicator for operational status
- Aviso de batería baixa
Que hai na caixa:
- Kidde Pi9010 Dual Sensor Smoke Alarm
- Soporte de montaxe
- Hardware de montaxe
- Batería de 9 voltios
- Manual de usuario
3. Configuración e instalación
3.1 Instalación da batería
The Kidde Pi9010 smoke alarm operates on a standard 9-volt battery, which is included. Ensure the battery is correctly installed before mounting the alarm.
- Open the battery compartment on the back of the alarm.
- Connect the 9-volt battery to the battery clip, ensuring correct polarity.
- Coloque a batería no compartimento e peche a tapa con seguridade.
Figure 1: Battery installation in the Kidde Pi9010 smoke alarm.
3.2 Montaxe da alarma
Select a suitable location for your smoke alarm, typically on the ceiling or high on a wall, away from corners and obstructions. Use the provided mounting bracket and hardware.
- Attach the mounting bracket to the ceiling or wall using the screws provided.
- Aliñe a alarma co soporte de montaxe e xire no sentido das agullas do reloxo ata que encaixe no seu lugar.
- Perform an initial test as described in Section 4.1.
4. Instrucións de funcionamento
4.1 Proba da alarma
Test your smoke alarm weekly to ensure it is functioning correctly.
- Press and hold the test/reset button located on the front of the alarm.
- The alarm will sound a loud, pulsating horn. Release the button once the horn sounds.
- Se a alarma non soa, consulte a sección Resolución de problemas.
4.2 Función de silencio
The Hush feature temporarily silences the alarm for approximately seven minutes during non-emergency situations, such as cooking fumes.
- To activate, press the Hush button when the alarm is sounding due to a nuisance condition.
- The alarm will silence, and the red LED will flash every 30-40 seconds to indicate it is in Hush mode.
- After approximately seven minutes, the alarm will automatically reset. If smoke is still present, the alarm will sound again.
Video 1: Official Kidde video demonstrating the Dual Photoelectric & Ionization Sensor Smoke Detector. This video provides a visual overview of the product's features and benefits.
5. Mantemento
5.1 Substitución da batería
The alarm will emit a brief chirp every 30 to 40 seconds for at least seven days when the 9-volt battery needs replacement.
- Twist the alarm counter-clockwise to remove it from the mounting bracket.
- Open the battery compartment and disconnect the old 9-volt battery.
- Connect a new 9-volt battery, ensuring correct polarity, and close the compartment.
- Reattach the alarm to the mounting bracket and test its operation.
5.2 Cleaning Your Alarm
Clean your smoke alarm regularly to prevent dust and debris from interfering with its operation.
- Use a soft brush attachment on your vacuum cleaner to gently remove dust from the alarm's cover and vents.
- Do not use water, cleaners, or solvents, as these can damage the unit.
6 Solución de problemas
| Problema | Causa posible | Solución |
|---|---|---|
| A alarma sona cada 30-40 segundos | Batería baixa | Replace the 9-volt battery (see Section 5.1). |
| Nuisance alarms (e.g., from cooking) | Smoke or steam from non-fire sources | Use the Hush feature (see Section 4.2). Ventilate the area. |
| A alarma non soa durante a proba | Battery not installed or dead; unit malfunction | Check battery installation/replace. If problem persists, replace unit. |
| Alarm sounds continuously without smoke | Dust buildup; unit malfunction | Clean the alarm (see Section 5.2). If problem persists, replace unit. |
7. Especificacións
- Marca: Kidde
- Número de modelo: Pi9010 (Manufacturer Part Number: 21026062-N)
- Fonte de enerxía: Batería de 9 voltios
- Tipo de sensor: Ionization and Photoelectric (Dual Sensor)
- Tipo de alarma: Audible
- Cor: Branco
- Dimensións: Approximately 5.75 inches (diameter) x 1.8 inches (depth)
- Temperatura de funcionamento: 40 °C (4.4 °F) a 100 °C (37.8 °F)
- Rango de humidade: 10-95% de humidade relativa, sen condensación
- Certificacións: Listado UL
- UPC: 047871260621
8. Garantía e soporte
The Kidde Pi9010 Dual Sensor Smoke Alarm is backed by a 10 ano de garantía limitada. This warranty covers defects in materials and workmanship from the date of purchase.
For complete warranty details, technical support, or assistance with your product, please refer to the full user manual included in the packaging or visit the official Kidde websitio.
Contact your local fire department for additional fire preparedness tips and safety information.