Manual do usuario da bomba de circulación IBO OHI 25-60/180

1. Produto rematadoview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

As características principais inclúen:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• Compact design for easy installation.
• Operación silenciosa.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. Información de seguridade

Lea atentamente todas as instrucións antes da instalación e o funcionamento. O incumprimento destas instrucións pode provocar descargas eléctricas, incendios ou lesións graves.

• Seguridade eléctrica: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• Temperatura da auga: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• Presión: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• Entorno de instalación: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• Equipos de protección individual: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. Guía de instalación

Proper installation is crucial for the pump's efficient and safe operation.

3.1 Comprobacións previas á instalación

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 Montaxe da bomba

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 Conexión eléctrica

1. Ensure the main power supply is switched off at the circuit breaker.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. Asegurar a correcta posta a terra.

3.4 System Filling and Venting

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. Instrucións de funcionamento

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 Posta en marcha inicial

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

4.2 Axustes de velocidade

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• Nivel I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• Nivel II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• Nivel III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. Mantemento

Un mantemento regular garante a lonxevidade e o funcionamento eficiente da súa bomba de circulación.

5.1 Comprobacións de rutina

• Inspección visual: Periodically check the pump for any signs of leaks, corrosion, or damage to the casing or electrical connections.
• Nivel de ruído: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• Temperatura: Ensure the pump is not overheating.

5.2 Limpeza

Keep the exterior of the pump clean and free from dust and debris to ensure proper heat dissipation.

5.3 Preparación para o inverno (se corresponde)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6 Solución de problemas

Esta sección ofrece orientación para problemas comúns. Para problemas complexos, consulte cun técnico cualificado.

7. Especificacións técnicas

8. Garantía e soporte

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.