DEWALT DCD771C2 Drill Driver and DCS391B Circular Saw Kit Instruction Manual

Introdución

This manual provides essential information for the safe and effective use of your DEWALT DCD771C2 20V MAX Cordless Lithium-Ion 1/2 inch Compact Drill Driver and DCS391B 20-Volt MAX Li-Ion Circular Saw Kit. Please read and understand all instructions before operating these tools. Keep this manual for future reference.

Instrucións xerais de seguridade

AVISO: Lea todas as advertencias de seguridade, instrucións, ilustracións e especificacións proporcionadas con esta ferramenta eléctrica. O incumprimento de todas as instrucións que se indican a continuación pode producir descargas eléctricas, incendios e/ou lesións graves.

Seguridade da zona de traballo

• Manter a zona de traballo limpa e ben iluminada. As zonas desordenadas ou escuras invitan a accidentes.
• Non utilice ferramentas eléctricas en atmosferas explosivas, como en presenza de líquidos, gases ou po inflamables. As ferramentas eléctricas crean faíscas que poden acender o po ou os fumes.
• Manteña os nenos e os espectadores afastados mentres manexa unha ferramenta eléctrica. As distraccións poden facer que perdas o control.

Seguridade Eléctrica

• Os enchufes das ferramentas eléctricas deben coincidir coa toma de corrente. Nunca modifique o enchufe de ningún xeito.
• Evite o contacto corporal con superficies conectadas a terra, como tubos, radiadores, cociñas e frigoríficos. Hai un maior risco de descarga eléctrica se o seu corpo está conectado a terra ou a terra.
• Non expoña as ferramentas eléctricas á choiva ou a condicións de humidade. A auga que entra nunha ferramenta eléctrica aumentará o risco de descarga eléctrica.

Seguridade persoal

• Mantéñase alerta, observa o que está a facer e use o sentido común ao manexar unha ferramenta eléctrica. Non use unha ferramenta eléctrica mentres estea canso ou baixo a influencia de drogas, alcohol ou medicamentos.
• Use equipos de protección individual. Use sempre protección ocular. Os equipos de protección, como unha máscara antipolvo, zapatos de seguridade antideslizantes, casco ou protección auditiva, que se utilicen nas condicións adecuadas, reducirán as lesións persoais.
• Evitar o arranque involuntario. Asegúrese de que o interruptor estea na posición de apagado antes de conectar a batería, coller ou transportar a ferramenta.

Compoñentes do produto

Your kit includes the following main components:

• DEWALT DCD771C2 20V MAX Cordless Lithium-Ion 1/2 inch Compact Drill Driver
• DEWALT DCS391B 20V MAX Li-Ion Circular Saw
• Batería de ións de litio de 20 V MAX
• Cargador de batería

DEWALT DCD771C2 20V MAX Cordless Drill Driver

Image: The DEWALT DCD771C2 20V MAX Cordless Drill Driver, featuring its yellow and black design, chuck, and battery connection point.

This compact drill driver is designed for a wide range of drilling and fastening applications. It features a 1/2 inch chuck and a two-speed transmission for versatility.

DEWALT DCS391B 20V MAX Circular Saw

Image: The DEWALT DCS391B 20V MAX Circular Saw, showing its blade, handle, and magnesium shoe.

The circular saw is engineered for demanding cutting tasks, offering a powerful motor and a durable magnesium shoe for accurate cuts. It supports a 0-50 degree bevel capacity.

Configuración e montaxe

Carga e instalación de baterías

1. Cargando a batería: Connect the charger to a standard power outlet. Slide the battery pack onto the charger until it clicks into place. The charger indicator light will show the charging status. Ensure the battery is fully charged before first use.
2. Instalación da batería: Align the battery pack with the battery port on the tool handle. Slide the battery into the tool until it locks securely.
3. Extracción da batería: Prema o botón de liberación da batería e deslice o paquete de baterías para sacala da ferramenta.

Drill Driver Setup

1. Abrindo o mandril: Rotate the chuck counter-clockwise until the jaws are wide enough to accept the drill bit or accessory.
2. Installing a Bit: Insert the desired drill bit or accessory into the chuck. Ensure it is centered.
3. Apertando o mandril: Rotate the chuck clockwise until the bit is firmly secured. Hand-tighten for best grip.

Image: A user operating the DEWALT DCD771C2 Drill Driver to fasten a screw into a wooden surface.

Circular Saw Setup

1. Instalación da lámina: Ensure the tool is disconnected from the battery. Press the spindle lock button and use the provided wrench to loosen the blade bolt. Place the blade onto the arbor with the teeth pointing in the direction of rotation (usually indicated by an arrow on the blade and tool). Re-tighten the blade bolt securely.
2. Axuste da profundidade de corte: Loosen the depth adjustment lever. Move the shoe up or down to set the desired cutting depth. Ensure the blade extends approximately 1/8 inch (3mm) below the workpiece. Tighten the lever.
3. Axuste do ángulo do bisel: Loosen the bevel adjustment lever. Tilt the shoe to the desired angle (0-50 degrees). Tighten the lever.

Operación

Drill Driver Operation

1. Selección de velocidade: Use the speed selector switch located on top of the tool to choose between high speed (2) for drilling and low speed (1) for fastening or larger diameter drilling.
2. Forward/Reverse Control: The forward/reverse button near the trigger controls the direction of rotation. Push left for forward, right for reverse, and center for lock-off.
3. Operating the Trigger: Squeeze the trigger to start the tool. Variable speed is controlled by the amount of trigger depression.
4. Perforación: Apply steady, even pressure. For hard materials, use slower speeds.

Operación de serra circular

1. Comezando a serra: Asegúrese de que a peza de traballo estea firmemente clamped. Depress the trigger lock-off button, then squeeze the trigger to start the saw. Allow the blade to reach full speed before contacting the workpiece.
2. Facer un corte: Guide the saw along the cutting line, maintaining a firm grip. Do not force the saw; let the blade do the work. Keep both hands on the tool handles during operation.
3. Precaucións de seguridade: Always ensure the lower blade guard operates freely. Never tie or wedge the guard in the open position. Avoid cutting small pieces that cannot be securely held.

Image: A user operating the DEWALT DCS391B Circular Saw to cut a sheet of plywood.

Mantemento

Un mantemento regular garante un rendemento óptimo e prolonga a vida útil das túas ferramentas.

• Limpeza: Keep the tool's ventilation openings clear of dust and debris. Use a soft brush or compressed air to clean the tool. Do not use water or chemical cleaners.
• Blade Care (Circular Saw): Regularly inspect the saw blade for sharpness and damage. Replace dull or damaged blades promptly. Ensure the blade is clean and free of resin buildup.
• Coidado da batería: Garde as baterías nun lugar fresco e seco, lonxe da luz solar directa. Non garde as baterías descargadas durante períodos prolongados.
• Inspección: Periodically check all screws and fasteners for tightness. Inspect cords and connections for damage.

Resolución de problemas

Especificacións

• Marca: DEWALT
• Fonte de enerxía: Alimentado por batería (20 V máx. de ións de litio)
• Drill Driver (DCD771C2):
  • Maximum Chuck Size: 0.5 inches
  • Number of Speeds: 2 (0-450 RPM / 0-1500 RPM)
  • Maximum Power: 300 Unit Watts Out (UWO)
  • Drilling Capacity (Wood/Metal): 0.5 inches
• Circular Saw (DCS391B):
  • Velocidade de rotación máxima: 5150 RPM
  • Maximum Power: 460 MWO
  • Bevel Capacity: 0-50 degrees
  • Shoe Material: Magnesium
• Números de modelo: DCD771C2 (Drill Driver), DCS391B (Circular Saw)
• Tipo de material: Metal With Magnesium And Plastic Components

Garantía e Soporte

For warranty information, service, or technical support, please refer to the official DEWALT website or contact DEWALT customer service. Keep your purchase receipt as proof of purchase.

DEWALT Contact Information:

• Websitio: www.dewalt.com
• Consulte a embalaxe do produto ou a documentación oficial website for specific regional contact numbers.