HEIMAN Z-Wave Carbon Monoxide Detector User Manual

1. Introdución

This manual provides essential information for the installation, operation, and maintenance of your HEIMAN Z-Wave Carbon Monoxide Detector. This device is designed to detect carbon monoxide (CO) gas and alert you to its presence, integrating with your Z-Wave smart home system for enhanced safety.

The HEIMAN Z-Wave Carbon Monoxide Detector is a compact, high-quality device, recognized as a Reddot winner in 2017. It operates on the Z-Wave 868.42 MHz frequency, suitable for the Europe version, and is compatible with various Z-Wave gateways such as Zipato, Fibaro, Vera, and SmartThings.

Figure 1: HEIMAN Z-Wave Carbon Monoxide Detector, front view.

2. Información importante de seguridade

• This device is a carbon monoxide detector and is not designed to detect smoke, fire, or other gases.
• Non pinte o detector. A pintura pode obstruír as aberturas do sensor e impedir que a unidade funcione correctamente.
• Do not block the ventilation openings on the detector.
• Test the detector regularly as described in the "Operating" section.
• The detector requires a CR123A battery. Use only recommended battery types.
• Non intente reparar o dispositivo vostede mesmo. Encargue calquera mantemento a persoal cualificado.
• Carbon monoxide is an invisible, odorless, and tasteless gas. This detector is designed to alert you to its presence, but it does not prevent CO from occurring.

3. Configuración e instalación

3.1 Instalación da batería

1. Twist the base of the detector counter-clockwise to open the battery compartment.
2. Insert one CR123A battery into the compartment, ensuring correct polarity (+/-).
3. Remove the protective pull tab if present.
4. Close the battery compartment by aligning the base and twisting clockwise until it clicks securely.

Figura 2: Traseira view of the detector with the battery compartment open, showing the CR123A battery.

Figure 3: Inserting the CR123A battery into the detector.

3.2 Montaxe do detector

The detector can be mounted on a wall or ceiling. Carbon monoxide is slightly lighter than air and mixes readily with it. For optimal detection, install the detector:

• In or near sleeping areas.
• On every level of your home.
• At least 1.5 meters (5 feet) from fuel-burning appliances.
• Avoid mounting in corners, near windows, doors, or areas with high airflow.

1. Escolla un lugar axeitado.
2. Use the provided screws and anchors to secure the mounting plate to the wall or ceiling.
3. Attach the detector to the mounting plate by aligning it and twisting clockwise until it locks into place.

Figure 4: HEIMAN Z-Wave Carbon Monoxide Detector mounted on a ceiling.

3.3 Z-Wave Network Inclusion/Exclusion

To integrate the detector into your Z-Wave network:

1. Put your Z-Wave gateway into inclusion (pairing) mode. Refer to your gateway's manual for specific instructions.
2. Press the Z-Wave button on the detector three times quickly. The detector will send an inclusion request to the gateway.
3. Once successfully included, the detector will appear in your gateway's device list.
4. To exclude the device, put your Z-Wave gateway into exclusion mode and press the Z-Wave button on the detector three times quickly.

4. Funcionamento

4.1 LED Indicators and Sound Patterns

The detector uses a combination of LED flashes and beeps to indicate its status:

• Prequecemento: Red LED flashes and four beeps.
• Alarma de CO: O LED verde parpadea cada 50 segundos.
• Normal Detection: Single beep every 50 seconds.
• Batería baixa: Dous pitidos cada 10 segundos.
• Mal funcionamento: Red LED flashes every 10 seconds, with CO alarm and silent.

Note: The text on the battery in Figure 2 provides a summary of these indicators.

4.2 Testing the Detector

Recoméndase probar o detector de CO semanalmente para garantir o seu correcto funcionamento.

1. Manteña premido o botón de proba do detector durante uns segundos.
2. The detector will emit a series of loud beeps and the LED will flash, indicating that the alarm and sensor are functioning correctly.
3. Release the button. The detector will return to normal operation.

5. Mantemento

5.1 Substitución da batería

The detector is powered by one CR123A battery with an estimated lifespan of 3 years. When the battery is low, the detector will emit two beeps every 10 seconds. Replace the battery immediately when this occurs.

1. Twist the base of the detector counter-clockwise to open the battery compartment.
2. Retire a batería CR123A antiga.
3. Insert a new CR123A battery, observing correct polarity.
4. Close the battery compartment by twisting clockwise until it clicks securely.
5. Proba o detector despois de substituír a batería.

5.2 Limpeza

Clean the detector regularly to prevent dust and debris from affecting its performance.

• Use un suave, damp cloth to wipe the exterior of the detector.
• Non use produtos de limpeza nin disolventes.
• Non pintar o detector.
• Gently vacuum around the sensor openings with a soft brush attachment to remove dust.

6 Solución de problemas

7. Especificacións

• Marca: HEIMAN
• Modelo: B0851P3WTH
• Fonte de enerxía: 1 x batería CR123A
• Duración da batería: Aproximadamente 3 anos
• Tipo de sensor: Electroquímica
• Frecuencia de onda Z: 868.42 MHz (Europe Version)
• Compatibilidade: Z-Wave Plus certified gateways (e.g., Zipato, Fibaro, Vera, SmartThings)
• Estilo: Moderno
• Fabricante: HEIMAN
• UPC: 345932281906

8. Garantía e soporte

For warranty information and technical support, please refer to the official HEIMAN websitio web ou póñase en contacto co seu distribuidor local. Garde o recibo da compra como proba de compra.