iRobot 4757625

iRobot Edge-Sweeping Brush Instruction Manual

For Roomba i, e, j Series & Combo 10 Max Robots

Introdución

The iRobot Edge-Sweeping Brush is an essential component designed to enhance the cleaning performance of your Roomba robot vacuum. This brush is specifically engineered to reach into corners and along wall edges, directing debris into the robot's main cleaning path for efficient removal.

Regular replacement of the Edge-Sweeping Brush ensures your Roomba maintains optimal cleaning effectiveness, preventing dirt and dust accumulation in hard-to-reach areas.

iRobot Edge-Sweeping Brush

Image: The iRobot Edge-Sweeping Brush, designed for effective corner and edge cleaning.

Compatibilidade

This Edge-Sweeping Brush is compatible with the following iRobot Roomba models:

  • Roomba Combo® robots
  • Roomba® i Series robots
  • Roomba® e Series robots
  • Roomba® j Series robots
  • Roomba Combo® 10 Max robots

Ensure your Roomba model is listed above for proper fit and function.

Setup: Installation Instructions

Replacing the Edge-Sweeping Brush is a simple process that can be completed with a coin or a small screwdriver.

  1. Step 1: Prepare the Robot. Turn your Roomba robot vacuum upside down on a clean, flat surface to access the underside.
  2. Step 2: Locate the Brush. Identify the existing Edge-Sweeping Brush, typically located on one side of the robot's underside.
  3. Step 3: Remove the Old Brush. Use a coin or a small screwdriver to unscrew the fastener holding the brush in place. Once unscrewed, gently pull the old brush upwards to remove it.
  4. Step 4: Install the New Brush. Align the new Edge-Sweeping Brush with the post on the robot's underside. Press it down firmly until it clicks into place.
  5. Step 5: Secure the New Brush. Use the coin or screwdriver to tighten the fastener, ensuring the new brush is securely attached. Do not overtighten.
Roomba cleaning on hardwood floor

Image: A Roomba robot vacuum cleaning a hardwood floor, demonstrating its operational environment.

Principios de funcionamento

The Edge-Sweeping Brush operates by rotating at a specific angle (27 degrees) to effectively dislodge and sweep debris from edges, corners, and other hard-to-reach areas. This debris is then guided into the robot's main cleaning path, where it is vacuumed up by the primary brushes and suction system.

The brush's design ensures comprehensive cleaning coverage, complementing the robot's main cleaning functions to leave floors thoroughly clean.

Roomba cleaning around scattered popcorn

Image: A Roomba robot vacuum demonstrating its cleaning capability by sweeping up scattered popcorn.

Mantemento

For optimal cleaning performance, it is recommended to inspect and clean the Edge-Sweeping Brush regularly. Hair and debris can become entangled in the bristles, reducing effectiveness. If the bristles appear worn, bent, or damaged, it is time to replace the brush.

Worn brushes are less effective at sweeping debris, which can impact your Roomba's overall cleaning efficiency. The replacement process is identical to the installation steps outlined in the "Setup" section.

Protect your iRobot investment with genuine parts

Image: Emphasizing the importance of using genuine iRobot parts for maintaining robot performance and protecting your investment.

Resolución de problemas

  • Brush Not Sweeping Effectively:
    • Check for tangled hair or debris around the brush and its post. Clean as necessary.
    • Inspect the bristles for wear or damage. If worn, replace the brush.
    • Ensure the brush is securely fastened with the screw.
  • Brush Detaches During Operation:
    • Verify that the brush screw is tightened properly.
    • Confirm that the brush is an authentic iRobot replacement part and compatible with your specific Roomba model. Non-OEM parts may not fit securely.

Especificacións

MarcaiRobot
Nome do modeloRoomba E I J Series Edge-Sweeping Brush
Número de modelo4757625
Compoñentes incluídosBrush (3-pack)
Característica especialLimpeza de bordos
Recomendación de superficieCarpet, Hardwood, Hard Surfaces
Dimensións do artigo (L x W x H)3.95 cm de longo x 4.6 cm de ancho x 0.63 cm de alto
GTIN / UPC885155031068

Información da garantía

This iRobot Edge-Sweeping Brush comes with a Garantía limitada do fabricante de 1 anos. For detailed terms and conditions, please refer to the official iRobot warranty documentation or contact iRobot customer support.

Note: Warranty coverage may be affected by the use of non-authentic replacement parts.

Apoio

For further assistance, technical support, or to purchase additional genuine iRobot replacement parts, please visit the official iRobot websitio ou póñase en contacto co seu departamento de atención ao cliente.

Official iRobot Store: Visit the iRobot Store on Amazon

© 2026 iRobot Corporation. Todos os dereitos reservados. Roomba é unha marca rexistrada de iRobot Corporation.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.