Maxxima 4 in. 5 CCT Ultra Thin Recessed LED Downlight Instruction Manual

Introdución

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Maxxima 4-inch 5 CCT Ultra Thin Recessed LED Downlight. Please read all instructions carefully before installation and retain this manual for future reference.

Imaxe: Fronte view of the Maxxima 4-inch 5 CCT Ultra Thin Recessed LED Downlight.

Información de seguridade

Para reducir o risco de incendio, descarga eléctrica ou lesións persoais, observe as seguintes precaucións de seguridade:

• Desconecte sempre a alimentación no disyuntor antes de comezar a instalación ou realizar calquera mantemento.
• Asegúrese de que todas as conexións eléctricas cumpran cos códigos e ordenanzas locais, así como co Código Eléctrico Nacional (NEC).
• Se non está seguro sobre o cableado, consulte a un electricista cualificado.
• Non o instale en lugares onde a temperatura de funcionamento supere a temperatura nominal do aparello.
• Este aparello é axeitado para damp locations and is IC Rated, meaning it is safe for direct contact with insulation.
• Do not modify the fixture or use it for purposes other than its intended use.

Contido do paquete

Comprobe que todos os compoñentes estean presentes antes de comezar a instalación:

• 1 x Maxxima 4 in. 5 CCT Ultra Thin Recessed LED Downlight
• 1 x Junction Box (J-Box) with integrated power supply
• Hardware de montaxe

Especificacións

Configuración e instalación

Siga estes pasos para a instalación correcta:

1. Apagar a enerxía: Before starting any electrical work, ensure the power supply to the installation area is turned off at the circuit breaker.
2. Preparación da abertura no teito: Cut a 4-inch diameter hole in the ceiling at the desired location. Ensure there are no obstructions such as joists or pipes.
3. Conectar cableado: Open the junction box cover. Connect the supply wires to the wires inside the junction box using the provided wire nuts:
   • Connect the black wire from the supply to the black wire of the J-Box.
   • Connect the white wire from the supply to the white wire of the J-Box.
   • Connect the ground wire from the supply to the green wire of the J-Box.
   Secure the junction box cover.

Image: The LED downlight connected to its junction box.
4. Seleccionar a temperatura da cor (CCT): Before inserting the light into the ceiling, locate the CCT selection switch on the side of the junction box. Choose your desired color temperature (2700K, 3000K, 3500K, 4000K, or 5000K) by sliding the switch.


Imaxe: Primeiro plano view of the CCT selection switch located on the side of the junction box.

5. Inserir caixa de conexións: Place the wired junction box into the ceiling opening.
6. Install Downlight: Connect the downlight to the junction box via the male/female connector. Push the spring clips on the sides of the downlight upwards and insert the fixture into the ceiling hole. The clips will automatically secure the light in place.


Imaxe: Lateral view of the downlight showing the tension spring clips used for installation.

7. Restaurar enerxía: Volve a conectar o interruptor.

Instrucións de funcionamento

Selección da temperatura da cor

The Maxxima 4-inch LED Downlight features 5 CCT (Correlated Color Temperature) options, allowing you to customize the light output to your preference. The selection switch is located on the side of the junction box.

• 2700K: Soft White (Warm, inviting light)
• 3000K: Warm White (Slightly brighter, still warm)
• 3500K: Bright White (Neutral, balanced light)
• 4000K: Neutral White (Cooler, more energetic light)
• 5000K: Daylight (Brightest, closest to natural daylight)

To change the CCT, you must access the junction box. It is recommended to select your preferred CCT before final installation into the ceiling. If changing after installation, ensure power is off before accessing the J-Box.

Image: Visual representation of the five selectable color temperatures.

Funcionalidade de atenuación

This LED downlight is dimmable from 20% to 100% when used with a compatible LED dimmer switch. Ensure your dimmer switch is rated for LED lighting to prevent flickering or damage to the fixture.

Mantemento

O downlight LED Maxxima require un mantemento mínimo.

• Limpeza: Asegúrese de que a electricidade estea desconectada antes de limpala. Limpe a luminaria cun pano suave, seco ou lixeiramente húmido.amp pano. Non empregue produtos de limpeza abrasivos nin disolventes, xa que poden danar o acabado ou os compoñentes eléctricos.
• Non hai pezas reparables polo usuario: A fonte de luz LED está integrada e non se pode substituír. Non intente abrir nin reparar a luminaria.

Resolución de problemas

If you encounter issues with your downlight, refer to the following table:

Garantía

This Maxxima LED Downlight is covered by a 3 ano de garantía desde a data de compra. Esta garantía cobre defectos de materiais e fabricación en condicións de uso normal. Para reclamacións de garantía ou máis detalles, póñase en contacto co servizo de atención ao cliente de Maxxima.

Atención ao cliente

For technical assistance, troubleshooting, or warranty inquiries, please contact Maxxima customer support. Refer to the product packaging or the official Maxxima websitio para obter información de contacto actual.

Please have your model number (MRL-S40905) and date of purchase available when contacting support.