LPSECURITY PY600ACN Sliding Gate Opener Control Board Instruction Manual

1. Introdución

This manual provides detailed instructions for the installation, operation, and maintenance of the LPSECURITY PY600ACN series control board for sliding gate openers. This PCB circuit board is designed for 220V systems and supports NC (Normally Closed) limit switches, as well as magnetic limit switches. Please read this manual carefully before installation and operation to ensure safe and efficient use.

2. Información de seguridade

Ensure all power is disconnected before performing any installation, wiring, or maintenance.
Installation should be performed by qualified personnel to prevent electric shock or damage to the equipment.
Verificar o voltage of your gate opener system (110V or 220V) matches the control board's specifications before connecting power.
Manteña os nenos e as mascotas lonxe da zona da porta durante o funcionamento.
Do not attempt to repair the control board yourself. Contact a qualified technician for service.

3. Produto rematadoview

3.1 Compoñentes

The LPSECURITY PY600ACN control board is a central component for managing sliding gate operations. It integrates various functionalities for gate control and safety.

Arriba view of the LPSECURITY PY600ACN control board, showing various terminals, relays, and a DIP switch. — Figura 1: Arriba view of the PY600ACN control board, highlighting connection terminals and main components.

En ángulo view of the LPSECURITY PY600ACN control board, showing the power transformer and terminal blocks. — Figura 2: En ángulo view of the control board, providing a clearer look at the power input and output sections.

3.2 Características principais

Control dun só botón: A single button can execute all control commands (close, open, stop).
Individual Remote Control Deletion: Ability to delete specific remote controls separately.
Interface completa: Supports infrared sensors, solar energy connections, button switches, photocells, and backup batteries.
Infrared Detection Connector: Equipped with a dedicated connector for infrared detection.
Voltage Opcións: Available in 110V and 220V versions.
Limit Switch Compatibility: Supports both mechanical and magnetic limit switches.

4. Especificacións

Atributo	Valor
Nome da marca	LPSECURIDADE
Número de modelo	PY600ACN (py)
Orixe	China continental
Certificación	CE
Use	Sliding gate circuit board
Voltage	220 V/110 V
Tipo de interruptor de límite	Magnetic limit switch controller (NC)
Aplicación	Sliding gate door controller
Entrada	Gate photocell lamp
Produto químico moi preocupante	Ningún
Plataforma de casa intelixente	Ningún

5. Configuración e instalación

5.1 Wiring the Control Board

Carefully connect all components to the control board as per the wiring diagram. Ensure correct polarity and secure connections for all wires.

Primeiro plano view of the control board terminals with various colored wires connected, indicating power, motor, and sensor inputs. — Figura 3: Example wiring connections on the control board. Note the green terminal blocks for various inputs and outputs.

5.2 Connecting the Limit Switch

The control board supports both mechanical and magnetic limit switches. Ensure the limit switch is properly connected and functioning. The video demonstrates connecting a magnetic limit switch and verifying its operation.

Video 1: Demonstration of connecting and testing the magnetic limit switch with the control board. Observe the LED indicators for proper function.

Steps for Limit Switch Connection and Test:

Connect the limit switch wires to the designated terminals on the control board.
Ensure the light on the control board corresponding to the limit switch is ON when the switch is activated (e.g., when the magnet is near the sensor).
Test the limit switch by manually moving the magnet past the sensor. The corresponding LED on the board should toggle ON/OFF.

5.3 Emparejamento de control remoto

To pair a remote control with the control board:

Press the "LEARN" button on the control board (refer to Figure 1 for location). The learning LED should illuminate.
While the learning LED is on, press any button on your remote control. The LED should flash or change state to indicate successful pairing.
Test the remote control by pressing the programmed button. The gate motor should respond (e.g., start moving).

6. Instrucións de funcionamento

Abrir/Pechar/Parar: Use the paired remote control or a connected button switch to operate the gate. A single press typically cycles through Open, Stop, Close, Stop.
Parada de emerxencia: In case of an emergency, press the remote control button again or the stop button to immediately halt the gate's movement.

7. Mantemento

Regularly inspect all wiring connections for signs of wear or damage.
Keep the control board clean and free from dust, moisture, and insects.
Check the functionality of the limit switches and safety sensors (e.g., photocells) periodically.
Ensure the remote control batteries are in good condition.

8 Solución de problemas

Problema	Causa posible	Solución
A porta non responde ao control remoto.	Remote not paired, remote battery low/dead, or incorrect remote.	Re-pair the remote control (Section 5.3). Replace remote battery. Ensure you are using the compatible remote control.
Gate does not stop at desired position.	Limit switch not properly connected or faulty.	Check limit switch wiring and functionality (Section 5.2). Adjust limit switch position if necessary.
Gate motor does not run.	No power to the board, motor wiring issue, or safety sensor activated.	Check power supply. Verify motor wiring. Ensure photocell or other safety sensors are not obstructed or faulty.

9. Consellos de usuario

Compatibilidade con control remoto: This control board is designed to work exclusively with LPSECURITY remote controllers. It is NOT compatible with other brands or universal remote controls.
Dispoñibilidade manual: The physical manual is not included in the package. Please request the digital manual from the seller via email after purchase.
Voltage and Limit Switch Type: Antes da compraasing or installing, always confirm that the control board's voltage (110V or 220V) and limit switch type (mechanical or magnetic) match your existing gate opener system.

10. Garantía e soporte

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact LPSECURITY Automation and Security Official Store directly. Keep your purchase records for faster service.