AMI BIOS Setup Program User Guide

Turn on or reboot the system.
When the screen appears with a series of diagnostic check, look
for the message “Hit if you want to run setup”.
Press the specified key to enter the BIOS setup screen.
Modify the settings as needed in the BIOS setup screen.
To exit, press the designated key. To save and exit, press the
corresponding keys.

Configuración CMOS estándar

Press the designated key for Standard CMOS Setup on the main
pantalla do menú.
Choose the item to modify using the arrow keys.
Modify the selected item using the designated keys.
After finishing with the Standard CMOS Setup, press the
designated key to go back to the main menu.

Configuración das características da BIOS

Press the designated key for BIOS Features Setup on the main
pantalla do menú.
Choose the item to modify using the arrow keys.
Modify the highlighted item using the designated keys.
After completing the modifications, press the designated key to
volver ao menú principal.

Preguntas frecuentes (FAQ)

Q: What should I do if I accidentally modify a setting in
BIOS?

A: If you accidentally modify a setting in BIOS, you can either
revert to the default settings by loading BIOS defaults or load
setup defaults depending on your requirement.

Q: How do I exit BIOS setup without saving changes?

A: To exit BIOS setup without saving changes, simply press the
designated key for exit without saving. This will discard any
modifications made during the current session.

Q: Is it necessary to enter BIOS setup for normal system
operación?

A: In general, entering BIOS setup is not required for normal
system operation. It is typically used for configuring hardware
settings or troubleshooting system issues.

View Fullscreen

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Capítulo 3
AMI® BIOS USER’S GUIDE
The system configuration information and chipset register information is stored in the CMOS RAM. This information is retained by a battery when the power is off. Enter the BIOS setup (if needed) to modify this information.
The following pages will describe how to enter BIOS setup, and all about options.

3-1

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Entra na configuración do BIOS
Enter the AMI® setup Program’s Main Menu as follows:
1. Turn on or reboot the system. The following screen appears with a series of diagnostic check.
AMIBIOS (C) 1999 American Megatrends Inc. AGIOMS VXXX XXXXXX Hit <DEL> if you want to run setup

(C) American Megatrends Inc. 61-XXXX-001169-00111111-071592-i82440FX-H
2. When the “Hit <DEL>” message appears, press <DEL> key to enter the BIOS setup screen.
3. Despois de premer tecla, aparecerá a pantalla de configuración da BIOS.

Note: If you don’t want to modify CMOS original setting, then don’t press any key during the system boot.
3-2

CAPÍTULO 3

AMI® BIOS USERS GUIDE

AMIBIOS HIFLEX SETUP UTILITIES – VERSION 1.30 (C) 1999 American Megatrends, Inc. All Rights
Reservado

Standard CMOS Feature BIOS Features Setup Chipset Features Setup Power Management Setup PnP/PCI Configuration Load Setup Defaults Load BIOS Defaults

Integrated Peripherals Hardware Monitor Setup Supervisor Password User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving

Esc: Quit FF5: Old Values

: Select Item (Shift)F2: Change Color

F7: Load Setup Defaults

F10: Gardar e saír

Time, Date, Hard Disk Type, …

4. Usa o e para mover o desprazamento destacado cara arriba ou abaixo.
5. Use the <ENTER> key to select the option.
6. To exit, press <ESC>. To save and exit, press <F10>.

3-3

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración CMOS estándar
1. Press <ENTER> on “Standard CMOS Setup” of the main menu screen .

Date (mm/dd/yyyy): Thu Oct 26, 2000 Time (hh/mm/ss): 19:22:43

TIPO

SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE

—————————————————————

Pri Master : Auto Pri Slave : Auto Sec Master : Auto Sec Slave : Auto

Unidade de disquete A: Unidade de disquete B:

1.44MB 3 1/2 Not Installed

Protección contra virus do sector de arranque desactivada

Base Memory : 640 Kb Other Memory: 384 Kb Extended Memory: 511 Mb Total Memory: 512 Mb

Detecting drive parameters: Press ESC to Abort

ESC:Exit : Select Item PU/PD/+/- : Modify (Shift) F2: Color

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar coa configuración CMOS estándar, prema para volver ao menú principal.

3-4

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración das características da BIOS
1. Press <ENTER> on “BIOS Features Setup” of the main menu screen.

Quick Boot Ist Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices BootUp Num-Lock Floppy Drive Swap Floppy Drive Seek Password Check L1 Cache Cache Bus ECC Video BIOS Cacheable

:Enabled :Floppy :IDE-O :CD-ROM :Yes :On :Disabled :Disabled :Setup :WriteBack :Disabled :Disabled

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar coa configuración das funcións da BIOS, prema para volver ao menú principal.

3-5

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:

Quick Boot Set this option to Enabled to permit AMI® BIOS to boot within 5
seconds. This option replaces the old ABOVE 1 MB Memory Test option.

1st Boot Device/2nd Boot Device/3rd Boot Device

This option sets the sequence of boot drives.

As configuracións son:

IDE 0

The system will boot from the first HDD.

IDE 1

The system will boot from the Second HDD.

IDE 2

The system will boot from the Third HDD.

IDE 3

The system will boot from the Fourth HDD.

Disquete

The system will boot from Floppy.

SCSI

The system will boot from the SCSI.

Rede

The system will boot from the Network drive.

CD-ROM

The system will boot from the CD-ROM.

ZIP A:/LS120 The system will boot from ZIP/LS120.

ATAPI ZIP C: The system will boot from ZIP.

Desactivar

Disable this sequence.

Try other Boot Devices This option sets the device boot, if all the Four Boot Devices failed.

Boot up Num Lock When this option is set to Off, AMI® BIOS turns off the Num Lock
key when the system is powered on. The end user can then use the arrow keys on both the numeric keypad and the keyboard. The settings are On or Off. The setup default and BIOS settings are On.

Floppy Drive Swap Set this option to Enabled to specify that floppy drives A: and B:
are swapped. The setting are Enabled and Disabled. The setup and BIOS default settings are Disabled.

3-6

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Floppy Drive Seek When this option is set to Enabled, AMI® BIOS performs a Seek
command on floppy drive A: before booting the system. The settings are Enabled and Disabled. The setup and BIOS default settings are Disabled.
Password Check This option specifies the type of AMI® BIOS password protection
that is implemented. The default settings is Setup.
L1 Cache Choosing Write Back allows it to write back the level 1 cache
memory. The settings are Write Back or Write through or Disabled.
Cache Bus ECC This option is for Pentium® 4 processor. During Enabled, this will
affect the system performance. Disabled this option if you don’t want to affect the system performance.
Video BIOS Cacheable Select Enabled allows caching of the video BIOS, resulting in
better system performance. However, if any program writes to this memory area, a system error may result. The settings are Enabled and Disabled.

3-7

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración das características do chipset

1. Press <ENTER> on “Chipset Features Setup” of the main menu screen.

CPU Frequency Ratio USB Function USB Keyboard Support Memory Hole Graphics Aperture Size ICH Decode Select CPU Bist Enable ICH Delayed Transaction ICH DCB Enable VGA Frame Buffer USWC PCI Frame Buffer USWC

:12.0X :Enabled :Disabled :Disabled :64MB :Subtractive :Disabled :Disabled :Disabled :Disabled :Disabled

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar coa configuración das funcións do chipset, prema para volver ao menú principal.

3-8

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:
CPU Frequency Ratio This option enables you to set the CPU ratio.
USB Function Set this option to Enabled or Disabled the on-chip USB controller.
USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
Memory Hole This option allows the end user to specify the location of a memory
hole. The cycle matching the selected memory hole will be passed to the ISA bus. If Enabled, the selected hole is not remapped.
Graphics Aperture Size This option determines the effective size of the graphics aperture
used in the particular PAC configuration. The AGP aperture is memorymapped, while graphics data structure can reside in a graphics aperture. The aperture range should be programmed as not cacheable in the processor cache, accesses with the aperture range are forwarded to the main memory, then PAC will translate the original issued address via a translation table which is maintained on the main memory. The option allows the selection of an aperture size of 4MB, 8MB, 16MB, 32MB, 64MB, 128MB and 256MB.

3-9

CAPÍTULO 3

AMI® BIOS USERS GUIDE

ICH Decode Select This option allows you to select the PCI decode timing of ICH.
CPU BIST Enable This option allows you Enable or Disable the CPU Built-In Self
Proba.
ICH Delayed Transaction The chipset has an embedded 32-bit posted write buffer to support
delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.
ICH DCB Enable This option allows you to Enable or Disable the ICH DMA
Collection Buffer for LPC I/F.
VGA Frame Buffer USWC This option allows you to Enable or Disable the VGA frame buffer.
PCI Frame Buffer USWC This option allows you to Enable or Disable the PCI frame buffer.

3-10

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración da xestión de enerxía
1. Press <ENTER> on “Power Management Setup” of the main menu screen.

IPCA Function

: Si

Resume By Alarm

Estado de sono

:S1/POS Alarm Date

Sleep State LED

:DualColor Alarm Hour

Standby Time Out (Minute) :Disabled Alarm Minute

Keyboard & PS/2 Mouse

:Monitor Alarm Second

FDC/LPT/COM Ports

:Monitor

SB & MSS Audio Ports

:Ignore

Portos MIDI

:Ignore

ADLIB Ports

:Ignore

Primary Master IDE

:Monitor

Primary Slave IDE

:Ignore

Secondary Master IDE

:Monitor

Secondary Slave IDE

:Ignore

System Thermal

:Ignore

Función do botón de acendido

:On/Off

Restore on AC/Power Loss :Last State

Wake Up On Ring

: Desactivado

Wake Up On Lan

: Desactivado

Wake Up On PME

: Desactivado

:Disabled :15 :12 :30 :30

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar coa configuración da xestión de enerxía, prema para volver ao menú principal.

3-11

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:
IPCA Function This item allows you to Enabled/Disabled the Advanced Configura-
tion and Power Management (ACPI). The settings are Enabled and Disabled.
Sleep State This option allows you to set which Sleep State will be used. S1/POS – Power on Suspend. The S1 sleeping state is a low wake-up latency sleeping state. In
this state, no system context is lost (CPU or chipset) and hardware maintains all system context.
S3/STR – Suspend to RAM. The S3 state is a low wake-up latency sleeping state where all system context is lost except the system memory. CPU,cache, and chipset context are lost in this state. Hardware maintains memory context and restores some CPU and L2 configuration context.
Sleep State LED This option determines which state the Power LED will use. The
settings are Blinking, Dual and Single. During Blinking, the power LED will blink when the system enters the suspend mode. When the mode is in Dual, the power LED will change its color. In Single mode, the power LED will always remain lit.

3-12

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Standby Time Out (Minute) This option specifies the length of a period of system inactivity
while in Standby state. When this length of time expires, the computer enters Suspend power state. The settings are Disabled, 1 min, 2 min, 4 min, 8 min, 10 min, 20 min, 30 min, 40 min, 50 min or 60 min.
Keyboard & PS/2 Mouse/ FDC/LPT/COM Ports/ SB & MSS Audio Ports/ MIDI Ports/ ADLIB Ports/ Primary Master IDE/Primary Slave IDE/Secondary Master IDE/Secondary Slave IDE/System Thermal
When set to Monitor, these options enabled event monitoring on the specified hardware interrupt request line. If set to Monitor and the computer is in a power saving state, AMI BIOS watches for activity on the specified IRQ line. The computer enters the full on power state if any activity occurs.
AMI BIOS reloads the Standby and Suspend time out timers if activity occurs on the specified IRQ line.
Power Button Function During Suspend, if you push the switch once, the system goes
into suspend mode and if you push it more than 4 seconds, the system will be turned off. During On/Off, the system will turn off once you push the switch.
Restore on AC/Power Loss The settings are power on, power off or last state. During power
on, after every AC power loss, the system will be turned on. During last status, after every AC power loss, whatever the system status, it will be the same when the AC power returns. During power off, after every AC power loss, the system will be turned off.

3-13

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Wake Up On Ring/Wake Up On LAN During Disabled, the system will ignore any incoming call from the
modem/LAN. During Enabled, the system will boot up if there’s an incoming call from the modem/LAN.

Note: If you have change the setting, you must let the system boot up until it goes to the operating system. Then, power off the system. This function will work the next time you power on.

Wake Up On PME This option enables the system to comply with PCI specification
version 2.2. PCI card should be present to enable power on or resume from the PME signal.

Resume By Alarm

This function is for setting the Date, Hour, Minute, and Second for

your computer to boot up. During Disabled, you cannot use this function.

During Enabled, Choose the Date, Hour, Minute, and Second:

Data da alarma

Select which day the system will boot up.

Hora de alarma

Select the hours for the system to boot up.

Alarm Minute Select the minutes for the system to boot up.

Alarm Second Select the seconds for the system to boot up.

Note: If you have change the setting, you must let the system boot up until it goes to the operating system. Then, power off the system. This function will work the next time you power on.

3-14

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración PNP/PCI
1. Press <ENTER> on “PNP/PCI Configuration” of the main menu screen.

Clear ESCD PCI VGA Palette Snoop DMA Channel 0 DMA Channel 1 DMA Channel 3 DMA Channel 5 DMA Channel 6 DMA Channel 7 IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15

:No :Disabled :PnP :PnP :PnP :PnP :PnP :PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP :PCI/PnP

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar coa configuración PNP/PCI, prema para volver ao menú principal.

3-15

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:
Clear ESCD During Yes, this will clear ESCD data on every boot.
PCI VGA Palette Snoop When this option is set to Enabled, multiple VGA devices operating
on different buses can handle data from the CPU on each set of palette registers on every video device. Bit 5 of the command register in the PCI device configuration space is the VGA Palette Snoop bit (0 is disabled). For example, if there are two VGA devices in the computer (one PCI and ISA) and the Bit settings are:
Disabled-Data read and written by the CPU is only directed to the PCI VGA device’s palette registers.
Enabled – Data read and written by the CPU is directed to both the PCI VGA device’s palette registers and the ISA VGA device palette registers, permitting the palette registers of both devices to be identical.
This option must be set to Enabled if an ISA adapter card requires VGA palette snooping. The settings are Enabled or Disabled.
DMA Channel 0/1/3/5/6/7 These options specify the bus that the specified DMA channel is
used. These options allow you to reserve DMAs for legacy ISA adapter cards.
These options determine if AMI® BIOS should remove a DMA from the available DMAs passed to devices that are configurable by the system BIOS. The available DMA pool is determined by reading the ESCD NVRAM. If more DMAs must be removed from the pool, the end user can use these options to reserve the DMA by assigning an ISA/EISA setting to it.

3-16

CAPÍTULO 3

AMI® BIOS USERS GUIDE

IRQ3/IRQ4/IRQ5/RQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15 These options specify the bus that the specified IRQ line is used on.
These options allow you to reserve IRQs for legacy ISA adapter cards. These options determine if AMI® BIOS should remove an IRQ from
the pool of available IRQs passed to devices that are configurable by the system BIOS. The available IRQ pool is determined by reading the ESCD NVRAM. If more IRQs must be removed from the pool, the end user can use these options to reserve the IRQ by assigning an ISA/EISA setting to it. Onboard I/O is configured by AMI® BIOS. All IRQs used by onboard I/O are configured as PCI/PnP. If all IRQs are set to ISA/EISA and IRQ14 and 15 are allocated to the onboard PCI IDE, IRQ9 will still be available for PCI and PnP devices, because at least one IRQ must be available for PCI and PnP devices. The settings are ISA/EISA or PCI/PnP. The Optimal and Fail-Safe default settings are IRQ3 through 7 are ISA/EISA. The Optimal and Fail-Safe default settings PCI/PnP.

3-17

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Integrated Peripherals s
1. Press <ENTER> on “Integrated Peripherals” of the main menu screen.

Floppy Controller Serial Port A Serial Port B
Serial Port B Mode IR Duplex Mode IR Pin Select
CIR Port CIR IRQ Select
OnBoard Parallel Port Port Mode EPP Version Port IRQ Port DMA Channel
OnBoard Midi Port Midi IRQ Select
OnBoard Game Port On-Chip IDE AC97 Audio Controller AC97 Modem Controller

:Auto :Auto :Auto :Normal :Half Duplex :IRRX/IRTX :Disabled :10 :Auto :ECP :N/A :Auto :Auto :300 :9 :200 :Both :Auto :Auto

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. Despois de rematar cos periféricos integrados, prema para volver ao menú principal.

3-18

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:

Floppy Controller Set this option to Auto for the BIOS to automatically detect the
dispositivo

Serial Port A/Serial Port B Choose Auto, for the BIOS to automatically detect the device.

If the ISA add-on card has
COM1 COM2 COM3 COM4 (I/O:3F8H) (I/O:3F8H) (I/O:3E8H) (I/O:2E8H)

Onboard Serial port to be set at

PORTO 1

IRQ ASSIGNED PORT2

IRQ ASSIGNED

üü

DISABLED X DISABLED X

COM3

COM4

üü

COM1

COM2

Xü

COM2

COM3

üX

COM1

COM4

üX

COM4

DISABLED X

Xü

COM3

DISABLED X

üü

COM2

DISABLED X

üü

COM1

DISABLED X

COM1

COM2

COM3

COM1

COM3

üX

COM1

COM2

Xü

COM1

COM2

Note: If the onboard serial port interrupt and ISA add-on card interrupt are in conflict, the serial port will not work properly. Please disable one of the devices.

3-19

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Serial Port B Mode Choosing Normal will set the Serial Port B for normal use, not for IR
device. Choosing IrDA or Ask IR will set it for use with IR device using these protocols.
IR Duplex Mode Can be set as either Half or Full duplex.
IR Pin Select Set this option to IRRX/IRTX when using an internal IR device
which is connected to J5 connector.
Onboard CIR Port Setting Enabled, the system support consumer IR and your device
have to be connected to J5 connector.
CIR IRQ Select Select IRQ 3, 4, 9, 10 or 11 to support CIR Interrupt.

3-20

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Onboard Parallel Port Choose Auto, the BIOS automatically assigned onboard parallel
port to the available parallel port or disabled.

If the ISA add-on card has

Onboard parallel port to be set as

LPT1 I/O:378H
ü ü ü X ü X X
X

LPT2 I/O:278H
ü ü X ü X ü X
X

LPT3 I/O:3BCH
ü X ü ü X X ü
X

PORT ASSIGNED
Disabled LPT3 LPT2 LPT1 LPT2 LPT1 LPT1
LPT1

IRQ ASSIGNED
X 5 5 7 5 7 7
7

Note: If the onboard parallel port interrupt and ISA add-on card interrupt are in conflict, the parallel port will not work properly. Please disable one of the devices.
Port Mode This option allows user to choose the operating mode of the
onbaord parallel port. The settings are Normal, SPP/EPP or ECP mode.
EPP Version This option is for setting which EPP version will be used. The
settings are 1.7 and 1.9.

3-21

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Port IRQ If the onboard parallel mode is not on auto mode, the user can select
the interrupt line for onboard parallel port. We suggest that the user select the interrupt for the onboard parallel port as shown below:

Onboard parallel port set at
LPT1(378H) LPT2(278H) LPT3(3BCH)

Parallel Port IRQ
7 5 5

Port DMA Channel This option allows user to choose port DMA channel 1 to 3 for the
onboard parallel port on ECP mode.
OnBoard MIDI Port Choose 290H, 292H, 300H, 330H to support MIDI devices.
MIDI IRQ Select Choose 5, 7, 9, 10 to support MIDI device interrupt.
OnBoard Game Port Choose 200H, 208H to support Joystick device.
Note: If Hardware Audio is onboard, the three items above in the peripheral setup will not be shown.
On-Chip IDE Set this option to enable or disable on-chip IDE controller.
AC97 Audio/AC’97 Modem Controller Set this option to Auto for the BIOS to automatically detect the
AC97 audio and modem controller.

3-22

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Configuración do monitor de hardware

The Hardware Monitor Setup is used to set the CPU speed and monitor the current CPU Temperature, CPU Fan speed, Chassis Fan Speed, Power fan speed, Vcore, etc. This is only available if there is Hardware Monitor onboard.
1. Press <ENTER> on “Hardware Monitor Setup” of the main menu screen.

-==System Hardware Monitor==-

Intrusión no chasis

: Desactivado

Temperatura da CPU

:40OC/104OF

System Temperature :32OC/89OF

Velocidade do ventilador da CPU

: 0 RPM

Velocidade do ventilador do sistema

: 0 RPM

Velocidade do ventilador de potencia

: 4354 RPM

CPU VID

: 1.75V

Vcore

:1.648 V

1.8 V

:1.824 V

Vio

:3.312 V

+ 5.0 V

:5.223 V

+ 12.0 V

:11.376 V

- 12.0V

:-11.497 V

- 5.0V

:-4.926 V

Batería

:3.136 V

+5V SB

:5.090 V

ESC:Quit

: Seleccione elemento

F1: Axuda

PU/PD/+/- : Modificar

F5 :Old Values (Shift)F2: Color

F6: Cargar valores predeterminados da BIOS

F7: Cargar os valores predeterminados da configuración

2. Uso e para escoller o elemento e e teclas para modificar o elemento resaltado.
3. After you have finished with the Hardware Monitor Setup, press <ESC> to go back to the main menu.

3-23

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Description of the item on screen follows:
Chassis Intrusion Set this option to Enabled, Reset, or Disabled the chassis intrusion
detector. During Enabled, any intrusion on the system chassis will be recorded. The next time you turn on the system, it will show a warning message. To be able to clear those warning, choose reset. Afte clearing the message it will go back to Enabled.
CPU Temperature/System Temperature/CPU Fan Speed/ System Fan Speed/Power Fan Speed/CPU VID/Vcore/1.8V/Vio/ +5V/+12V/-12V/-5V/Battery/5VSB
This will show the CPU/Fan/System voltage chart and Fan speed.

3-24

CAPÍTULO 3

AMI® BIOS USERS GUIDE

Contrasinal supervisor/usuario
This Main Menu item lets you configure the system so that a password is required each time the system boots or an attempt is made to enter the Setup program. Supervisor Password allows you to change all CMOS settings but the User Password setting doesn’t have this function. The way to set up the passwords for both Supervisor and User are as follow:
1. Choose “Supervisor/User Password” in the Main Menu and press <Enter>. The following message appears:
“Enter New Supervisor/User Password:”
2. A primeira vez que execute esta opción, introduza só o contrasinal de ata 6 caracteres e prema . A pantalla non mostrará os caracteres introducidos. Se non hai contrasinal, só tes que premer .
3. Despois de introducir o contrasinal, aparece a seguinte mensaxe que lle solicita que confirme o contrasinal:
“Retype New Supervisor/User Password:”
4. Introduza exactamente o mesmo contrasinal que acaba de escribir para confirmar o contrasinal e prema .
5. Move o cursor ata Gardar e saír da configuración para gardar o contrasinal.
6. Se precisa eliminar o contrasinal que introduciu anteriormente, escolla o Contrasinal de supervisor/usuario e prema . Eliminará o contrasinal que tiña antes.
7. Move o cursor ata Gardar e saír da configuración para gardar a opción que fixo. En caso contrario, o antigo contrasinal seguirá estando alí a próxima vez que acenda a máquina.

3-25

CAPÍTULO 3

AMI® BIOS USERS GUIDE

IDE HDD Auto Detection
Podes usar esta utilidade para detectar automaticamente as características da maioría dos discos duros.

Date (mm/dd/yyyy): Fri Jul 21, 2000 Time (hh/mm/ss): 01:01:34

TIPO

SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE

—————————————————————

Pri Master : Pri Slave : Sec Master : Sec Slave :

Unidade de disquete A: Unidade de disquete B:

Not Installed Not Installed

Protección contra virus do sector de arranque desactivada

Base Memory : 0 KB Other Memory: 384 Kb Extended Memory : 0 Mb Total Memory : 1 Mb

Detecting drive parameters: Press ESC to Abort

ESC:Exit : Select Item PU/PD/+/- : Modify (Shift) F2: Color

3-26

Documentos/Recursos

	AMI BIOS Setup Program [pdfGuía do usuario BIOS Setup Program, Setup Program
	AMI BIOS Setup Program [pdfGuía do usuario BIOS Setup Program, Setup Program

Referencias

Manual de usuario

AMI BIOS Setup Program User Guide

Programa de configuración da BIOS

Información do produto

Especificacións:

Instrucións de uso do produto

Entrando na configuración da BIOS

Configuración CMOS estándar

Configuración das características da BIOS

Preguntas frecuentes (FAQ)

Q: What should I do if I accidentally modify a setting in
BIOS?

Q: How do I exit BIOS setup without saving changes?

Q: Is it necessary to enter BIOS setup for normal system
operación?

Documentos/Recursos

Referencias

Deixa un comentario

Cancelar resposta

Programa de configuración da BIOS

Información do produto

Especificacións:

Instrucións de uso do produto

Entrando na configuración da BIOS

Configuración CMOS estándar

Configuración das características da BIOS

Preguntas frecuentes (FAQ)

Q: What should I do if I accidentally modify a setting in BIOS?

Q: How do I exit BIOS setup without saving changes?

Q: Is it necessary to enter BIOS setup for normal system operación?

Documentos/Recursos

Referencias

Deixa un comentario

Cancelar resposta

Q: What should I do if I accidentally modify a setting in
BIOS?

Q: Is it necessary to enter BIOS setup for normal system
operación?