BLACK+DECKER RC800 8-Inch Saw Chain Instruction Manual

Introdución

The BLACK+DECKER RC800 8-Inch Saw Chain is designed for efficient pruning and wood cutting tasks. This compact and lightweight chain is engineered for easy replacement, ensuring your yard projects can be completed without interruption. It is specifically designed to replace dull chains on compatible BLACK+DECKER pole saws, maintaining optimal cutting performance.

Compatibilidade

The RC800 saw chain is compatible with the following BLACK+DECKER models:

• NPP 2018
• CS818

Ensure your chainsaw model matches the listed compatible models before installation.

Información de seguridade

Always prioritize safety when handling and operating chainsaws and their accessories. Failure to follow safety instructions can result in serious injury.

• Read the Chainsaw Manual: Always refer to your chainsaw's original instruction manual for specific safety guidelines and operating procedures.
• Usar equipo de protección individual (EPI): Always wear safety glasses or goggles, hearing protection, gloves, and appropriate footwear when working with chainsaws.
• Desconectar a enerxía: Before performing any maintenance, installation, or adjustment on the saw chain, ensure the chainsaw is turned off and disconnected from its power source (battery removed or unplugged).
• Manipular con coidado: Saw chains are sharp. Handle them carefully to prevent cuts.
• Tensión axeitada: Ensure the chain is correctly tensioned after installation to prevent it from derailing or causing kickback.

Instrucións de instalación

Follow these general steps to replace your BLACK+DECKER RC800 saw chain. Always consult your specific chainsaw model's manual for detailed instructions.

1. Preparar a motoserra: Ensure the chainsaw is turned off and disconnected from its power source. Place it on a stable, flat surface.
2. Remove the Bar Cover: Loosen and remove the nuts or knobs securing the side cover that holds the guide bar and chain. Carefully remove the side cover.
3. Remove the Old Chain: Remove the old saw chain from the guide bar and sprocket. Dispose of the old chain responsibly.
4. Install the New Chain:
   • Carefully uncoil the new BLACK+DECKER RC800 chain.
   • Place the chain around the drive sprocket (the gear that turns the chain).
   • Fit the chain into the groove of the guide bar, ensuring the cutting teeth are facing the correct direction. The sharp edges of the teeth should point towards the front of the guide bar, in the direction of rotation.
   • Slide the guide bar onto the mounting studs, ensuring the chain remains seated in the guide bar groove and around the sprocket.
5. Axustar a tensión da cadea:
   • Replace the side cover, but do not fully tighten the nuts/knobs yet.
   • Adjust the chain tensioning screw (if applicable to your model) until the chain is snug against the bottom of the guide bar, but can still be pulled freely by hand. There should be no slack on the underside of the bar.
   • A common test is to lift the chain in the middle of the bar; the drive links should not come out of the bar groove, and you should be able to see the bottom of the drive links.
6. Tighten the Cover: Once the tension is correct, fully tighten the side cover nuts/knobs. Recheck the chain tension after tightening.
7. Lubricate (if applicable): If your chainsaw requires manual lubrication, ensure the chain and bar are adequately oiled before use.

Image: The BLACK+DECKER RC800 8-Inch Saw Chain, ready for installation.

Operating the Saw Chain

Once the RC800 saw chain is correctly installed and tensioned on your compatible BLACK+DECKER chainsaw, it is ready for use. Always ensure the chain is properly lubricated and that all safety precautions outlined in your chainsaw's manual are followed. The chain is designed for efficient cutting of wood and pruning tasks.

Mantemento

Un mantemento regular prolonga a vida útil da cadea da serra e garante un funcionamento seguro.

• Afiado: Keep the chain teeth sharp. A dull chain will not cut efficiently and can cause excessive wear on the chainsaw. Refer to your chainsaw manual or a professional for proper sharpening techniques.
• Lubricación: Ensure the chain and guide bar are always adequately lubricated with appropriate bar and chain oil. This reduces friction and heat, preventing premature wear.
• Limpeza: After each use, clean sawdust, debris, and resin from the chain and guide bar. This prevents buildup that can hinder performance.
• Inspección: Regularly inspect the chain for damaged, bent, or broken links and teeth. Replace the chain if any significant damage is found.
• Almacenamento: Store the chain in a dry, clean place when not in use. Applying a light coat of oil can help prevent rust.

Resolución de problemas

If your new RC800 saw chain is not cutting effectively, consider the following common issues:

• Incorrect Chain Direction: The most common issue with a new chain not cutting is incorrect installation direction. Ensure the cutting teeth are oriented correctly, pointing towards the front of the guide bar in the direction of rotation. The smooth part (raker) should lead into the wood, followed by the cutting tooth.
• Cadea desafilada: Even new chains can sometimes benefit from a quick sharpening, or may have been dulled during initial use if cutting hard materials.
• Improper Tension: A chain that is too loose or too tight will not cut efficiently and can be dangerous. Adjust the tension as described in the installation section.
• Falta de lubricación: Insufficient oil can cause the chain to bind, overheat, and fail to cut properly. Ensure the oil reservoir is full and the oiling system is functioning.

Especificacións

Garantía e Soporte

Specific warranty details for the BLACK+DECKER RC800 8-Inch Saw Chain were not provided in the product data. For warranty information, technical support, or replacement parts, please contact BLACK+DECKER customer service or visit their official websitio. Garda sempre o comprobante de compra.