1. Introdución
This manual provides detailed instructions for the installation, operation, and maintenance of your Arc Audio FD2200 2-Channel Car Amplificador. Lea este manual detidamente antes de tentar instalar ou operar o amplifier to ensure proper function and safety.
2. Información de seguridade
Observe sempre as seguintes precaucións de seguridade:
- Disconnect the vehicle's battery before making any electrical connections.
- Asegúrate de que todo o cableado estea correctamente instalado e fixado para evitar danos ou curtocircuítos.
- Evite instalar o amplifer en lugares expostos á luz solar directa, á calor excesiva, á humidade ou ao po.
- Use appropriate gauge wiring for power and ground connections to prevent overheating.
- Consult a professional installer if you are unsure about any aspect of the installation.
3. Produto rematadoview
The Arc Audio FD2200 is a high-performance 2-channel car amplifier designed to deliver clear and powerful audio. It features robust construction and advanced protection circuits.
Image 1: Arc Audio FD2200 2-Channel Car Amplificador. Esta imaxe mostra a parte superior view da ampvidador, mostrarasing its black and silver casing with the Arc Audio logo and model number.
Características principais:
- 12dB stereo crossover with x10 range switch (55Hz to 5.5KHz)
- High/low/full range selector switch
- Mono/stereo/bridged select feature
- 18dB bass control at 45Hz
- Protection against reverse voltage, sobre voltage, speaker short, and thermal overload
- Construción resistente
4. Configuración e instalación
Unha instalación axeitada é crucial para un rendemento e unha seguridade óptimos. Recoméndase ter isto ampLiificador instalado por un profesional cualificado.
4.1 Localización de montaxe
Escolle unha localización de montaxe que sexa:
- Seco e ben ventilado.
- Protected from direct sunlight and excessive heat.
- Seguro e libre de vibracións.
- Accesible para cableado e axustes.
4.2 Conexións de cableado
Siga estas pautas para as conexións eléctricas:
- Potencia (B+): Conecte un cable de alimentación con fusible directamente do terminal positivo da batería do vehículo ao amplifier's B+ terminal. Ensure the fuse is located within 18 inches of the battery.
- Terra (GND): Connect a short, heavy-gauge ground cable from the ampo terminal GND do adaptador a unha superficie metálica limpa e sen pintar no chasis do vehículo.
- Remoto (REM): Conecta un cable de acendido remoto da saída remota da unidade principal ao ampterminal REM do vivificador.
- Entradas RCA: Conecte os cables RCA da toma de corrente da unidade principalamp saídas ao amptomas de entrada RCA do lificador.
- Saídas de altofalantes: Conecte os cables do altofalante desde o amplifier's speaker terminals to your speakers. Observe correct polarity (+ to + and - to -).
5. Instrucións de funcionamento
Unha vez instalado, o amplifier requires proper configuration for optimal audio performance.
5.1 Axuste de ganancia
O control de ganancia coincide co amplifier's input sensitivity to the output of your head unit. Start with the gain set to minimum and slowly increase it until you hear distortion, then back off slightly.
5.2 Axustes de crossover
Use the 12dB stereo crossover with the x10 range switch to set the desired frequency range for your speakers. The high/low/full range selector switch allows you to choose the appropriate mode:
- Paso alto: Filters out low frequencies, suitable for full-range speakers or tweeters.
- Pase baixo: Filters out high frequencies, suitable for subwoofers.
- Rango completo: Allows all frequencies to pass through, typically used for full-range speakers without a separate subwoofer.
5.3 Reforzo de graves
The 18dB bass control at 45Hz can be used to enhance low-frequency output. Use this feature sparingly to avoid distortion and potential speaker damage.
5.4 Mono/Stereo/Bridged Select
This switch allows you to configure the amplifier for different output modes:
- Estéreo: Standard 2-channel operation for two speakers.
- Mono: Combines both channels into a single output, typically for a single subwoofer.
- Ponte: Combines the power of both channels into a single, higher-power output, usually for a single, high-power subwoofer. Refer to the specifications for bridged power output.
6. Mantemento
The Arc Audio FD2200 ampO lificador require un mantemento mínimo para garantir un rendemento a longo prazo.
- Manteña o ampManteña o purificador limpo e libre de po e residuos. Use un pano suave e seco para a limpeza.
- Garantir unha ventilación adecuada ao redor amprefrigerador para evitar o sobrequecemento. Non bloquee as aletas de refrixeración.
- Comprobe periodicamente todas as conexións do cableado para comprobar se están ben apertadas e se presentan corrosión.
7 Solución de problemas
Se tes problemas co teu amplifier, consulte os seguintes problemas e solucións comúns:
| Problema | Causa posible | Solución |
|---|---|---|
| Sen enerxía/Sen son | Fusible fundido, cable de alimentación/terra/control remoto solto, amplifier en modo de protección. | Check fuses (battery and amplifier). Verify all power, ground, and remote connections are secure. Check for short circuits in speaker wiring. |
| Son distorsionado | Gain set too high, improper crossover settings, poor quality input signal. | Reduce gain. Adjust crossover settings. Check RCA cables for damage. |
| Ampsobrequecemento do lificador | Inadequate ventilation, impedance too low, prolonged high-power operation. | Asegurar un fluxo de aire axeitado arredor do amplifer. Verificar as coincidencias de impedancia do altofalante amplifier capabilities. Reduce volume or operating time. |
| Noise/Hissing | Ground loop, poor quality RCA cables, improper gain setting. | Ensure a solid ground connection. Use shielded RCA cables. Adjust gain. |
If the problem persists after attempting these solutions, contact Arc Audio customer support or a qualified service technician.
8. Especificacións
The following are the technical specifications for the Arc Audio FD2200 ampmáis vivo:
- Potencia de saída (RMS):
- 100 Watts x 2 @ 4 ohms
- 185 Watts x 2 @ 2 ohms
- 360 Watts x 1 @ 4 ohms (bridged)
- Transient Distortion: <0.1% @ 4 ohms
- Resposta en frecuencia: 20Hz - 20KHz
- Signal-to-Noise Ratio (A-weighted): > 98 dB
- Boost de baixo: +18 dB @ 45 Hz
- Sensibilidade de entrada: 250 mV - 2.5 V
- Crossover: 55Hz - 5.5KHz variable 12dB
- Fusible: 45 A x 1
- Dimensions (with endcaps): 10 3/8" x 16 3/4" x 2 3/8"
- Dimensions (without endcaps): 10 3/8" x 13 1/2" x 2 3/8"
- Peso do artigo: 12 libras
- Voltage: 12 voltios (DC)
9. Garantía e soporte
Arc Audio products are designed for reliability and performance. For warranty information, please refer to the warranty card included with your product or visit the official Arc Audio website. For technical support or service inquiries, please contact Arc Audio customer service directly.
Información de contacto:
- Websitio: www.arcaudio.com (Exampligazón, a ligazón real pode variar)
- Atención ao cliente: Consulte o websitio para os métodos de contacto actuais.
