Introdución
This manual provides instructions for the proper installation, operation, and maintenance of the LASCO 10-2431 Braided Vinyl Water Supply Line. This product is designed to connect most faucets to a water source, ensuring a reliable and lead-free connection.
The LASCO 10-2431 is a 1/2-inch Female Iron Pipe (FIP) by 1/2-inch Female Iron Pipe (FIP) by 30-inch flexible braided vinyl supply line. It is certified by the Uniform Plumbing Code (UPC) and meets California AB-1953, Vermont, and new federal standards for low lead applications, ensuring product quality and safety.
Image showing the LASCO 10-2431 braided vinyl water supply line, featuring its flexible design and connection ends.
Información de seguridade
- Peche sempre a subministración principal de auga antes de comezar calquera traballo de fontanería.
- Use equipo de protección individual axeitado, como lentes de seguridade, durante a instalación.
- Do not over-tighten connections, as this can damage the supply line or fittings.
- Asegúrate de que todas as conexións estean seguras para evitar fugas.
- This product is designed for water supply applications only. Do not use for gas or other non-water applications.
- The product is lead-free and complies with California AB-1953, Vermont, and federal low lead standards.
Contido do paquete
- 1 x LASCO 10-2431 Braided Vinyl Water Supply Line (1/2-Inch FIP x 1/2-Inch FIP x 30-Inch)
Configuración e instalación
Follow these steps to properly install your LASCO 10-2431 water supply line:
- Preparar a zona: Turn off the main water supply to the area where the installation will take place. Drain any residual water from the existing lines.
- Remove Old Supply Line (if applicable): Use an adjustable wrench to carefully disconnect the old supply line from both the faucet and the water stop valve. Have a bucket ready to catch any remaining water.
- Inspeccionar conexións: Ensure that the threads on both the faucet shank and the water stop valve are clean and free of debris.
- Conectar á billa: Hand-tighten one end of the LASCO 10-2431 supply line to the faucet shank. Once hand-tight, use an adjustable wrench to tighten an additional 1/4 to 1/2 turn. Do not over-tighten.
- Connect to Water Stop Valve: Hand-tighten the other end of the supply line to the water stop valve. Once hand-tight, use an adjustable wrench to tighten an additional 1/4 to 1/2 turn. Do not over-tighten.
- Comproba se hai torceduras: Ensure the supply line is not kinked or bent sharply, which could restrict water flow or damage the line.
- Restaurar o subministro de auga: Acende lentamente o abastecemento principal de auga.
- Inspeccionar por fugas: Carefully check all connections for any signs of leaks. If a leak is detected, turn off the water supply, tighten the connection slightly, and recheck.
Instrucións de funcionamento
Once installed, the LASCO 10-2431 water supply line operates passively to deliver water. Ensure the water supply is fully turned on at the stop valve and the main supply. Monitor for consistent water flow and absence of leaks, especially during the first few hours after installation.
Mantemento
- Inspección periódica: Periodically inspect the supply line for any signs of wear, corrosion, kinks, or leaks. It is recommended to check connections annually.
- Limpeza: The exterior of the braided vinyl can be wiped clean with a damp un pano se é necesario. Non empregue produtos químicos agresivos nin produtos de limpeza abrasivos.
- Substitución: If any damage or persistent leaks are observed, replace the supply line immediately with a new, compatible unit.
Resolución de problemas
| Problema | Causa posible | Solución |
|---|---|---|
| Fuga no punto de conexión | Loose connection, damaged washer, cross-threaded fitting | Turn off water supply. Gently tighten connection. If leak persists, disconnect, inspect washer for damage, and ensure threads are aligned before re-tightening. Replace if necessary. |
| Baixo caudal de auga | Kinked supply line, partially closed stop valve, debris in line | Check the supply line for kinks and straighten if found. Ensure the water stop valve is fully open. If problem persists, the line may need to be inspected for internal debris or replaced. |
| Visible damage to line | Physical impact, excessive bending, age-related wear | Turn off water supply immediately. Replace the damaged supply line with a new one. |
Especificacións
- Número de modelo: 10-2431
- Marca: LASCO
- Material: Braided Poly Vinyl
- Conexións: 1/2-Inch Female Iron Pipe (FIP) x 1/2-Inch Female Iron Pipe (FIP)
- Lonxitude: 30 polgadas
- Cor: Silver/Pewter
- Certificacións: Uniform Plumbing Code (UPC) certified, Lead-Free (meets California AB-1953, Vermont, and new federal standards)
- Peso do artigo: Aproximadamente 5.4 onzas (0.34 libras)
Garantía e Soporte
For specific warranty information regarding your LASCO 10-2431 Braided Vinyl Water Supply Line, please refer to the documentation provided at the time of purchase or contact LASCO customer support directly. General product support and technical assistance can be obtained through the manufacturer's official channels.
Fabricante: LASCO
Websitio: www.lascofittings.com (Exampligazón, verifica o fabricante real websitio)
Atención ao cliente: Consulte o fabricante websitio para os detalles de contacto.
