Manual de instrucións do receptor abridor de portas de garaxe Genie 36163R.S IntelliCode

1. Introdución

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Genie 36163R.S IntelliCode Garage Door Opener Receiver. This receiver is designed to enhance the compatibility of your garage door opener system with Genie IntelliCode remotes, operating on both 315MHz and 390MHz frequencies.

Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.

2. Contido do paquete

The Genie 36163R.S IntelliCode Receiver package includes:

• One (1) Genie 36163R.S IntelliCode Receiver unit.

Nota: This package contains the receiver unit only. Transmitters (remotes), wiring, and power packs are not included and must be acquired separately if needed. This receiver is commonly used as a component in the GIRUD-1T Receiver Kit.

3. Información de seguridade

Observe sempre as seguintes precaucións de seguridade:

• Disconnect power to the garage door opener before installing or servicing the receiver.
• Asegúrese de que todas as conexións de cableado estean seguras e cumpran cos códigos eléctricos locais.
• Keep hands and clothing clear of the garage door and its moving parts during operation.
• Do not allow children to operate the garage door opener or play with remote controls.
• Test the safety reversal system of your garage door opener after installation.

4. Configuración e instalación

The Genie 36163R.S receiver is designed for straightforward installation. Follow these steps:

4.1. Identify Components

Figura 1: Arriba view of the Genie 36163R.S IntelliCode Receiver. This image shows the overall compact design of the receiver unit.

Figura 2: Abaixo view of the Genie 36163R.S IntelliCode Receiver. The label displays the receiver model (315390R2) and FCC compliance information.

Figura 3: Lateral view of the Genie 36163R.S IntelliCode Receiver. This image highlights the POWER, COMMON, and WALLBUTTON TERMINAL connections, along with the LEARN CODE INDICATOR LED and LEARN CODE BUTTON.

4.2. Cableado do receptor

1. Desconectar a enerxía: Before making any connections, ensure the power to your garage door opener is disconnected at the circuit breaker.
2. Locate Terminals: On your garage door opener power head, locate the terminals for the wall control button. These are typically labeled "COMMON" and "WALL BUTTON" or similar.
3. Connect Receiver Wires:
   • Connect a wire from the receiver's "COMMON" terminal to the "COMMON" terminal on your garage door opener.
   • Connect a wire from the receiver's "WALLBUTTON TERMINAL" to the "WALL BUTTON" terminal on your garage door opener.
   • Connect the receiver's "POWER" terminal to a 24-volt power source. This may be available from your garage door opener's accessory terminals or require a separate 24V power pack (not included).
4. Conexións seguras: Asegúrese de que todas as conexións dos cables estean firmes e seguras.

4.3. Montaxe do receptor

Mount the receiver in a location that is protected from moisture and physical damage, preferably near the garage door opener. Ensure the antenna wire hangs freely and is not coiled or obstructed for optimal signal reception.

5. Operating Instructions: Programming Remotes

This receiver is compatible with Genie IntelliCode remotes. To program a remote to the receiver:

1. Restaurar enerxía: Reconnect power to your garage door opener. The LEARN CODE INDICATOR LED on the receiver should illuminate or flash.
2. Press Learn Button: Press and release the "LEARN CODE BUTTON" on the receiver (refer to Figure 3). The LEARN CODE INDICATOR LED will begin to flash slowly.
3. Activar o control remoto: Within 30 seconds, press and release the button on your IntelliCode remote control that you wish to program.
4. Confirmación: The LEARN CODE INDICATOR LED on the receiver will stop flashing and remain lit for a moment, then turn off, indicating successful programming.
5. Proba a distancia: Press the programmed button on your remote control to test the garage door opener's operation.
6. Program Additional Remotes: Repeat steps 2-5 for any additional IntelliCode remotes you wish to program.

Nota: If the remote does not operate the garage door, ensure the remote has fresh batteries and repeat the programming steps.

6 Solución de problemas

• Receiver not responding:
  • Check power connections to the receiver. Ensure 24V power is supplied.
  • Verify wiring to the garage door opener's wall button terminals is correct and secure.
  • Asegúrate de que o propio abridor da porta da garaxe teña corrente.
• Remote not operating door after programming:
  • Confirm the remote is a Genie IntelliCode remote.
  • Check the remote's battery. Replace if necessary.
  • Repita os pasos de programación con coidado.
  • Ensure the remote is within range of the receiver.
• Alcance remoto reducido:
  • Ensure the receiver's antenna wire is fully extended and not obstructed or coiled.
  • Check for sources of radio interference (e.g., other electronic devices, metal objects).
  • Consider relocating the receiver for better line-of-sight to where remotes are typically used.

7. Especificacións

8. Mantemento

The Genie 36163R.S IntelliCode Receiver requires minimal maintenance. Periodically:

• Inspeccione o cableado para detectar calquera sinal de desgaste ou danos.
• Ensure the receiver is free from dust and debris.
• Verify the antenna is unobstructed.

No user-serviceable parts are inside the receiver unit. Do not attempt to open or repair the unit yourself.

9. Garantía e soporte

For warranty information or technical support, please refer to the official Genie website or contact Genie customer service. Keep your purchase receipt for warranty claims.

Genie Customer Service: Refer to product packaging or the official Genie websitio para obter información de contacto actual.