1. Introdución
This manual provides comprehensive instructions for the GENIUS KILO TX2 JL remote control. Please read this manual carefully before using the device to ensure proper operation and to maximize its lifespan. Keep this manual for future reference.
2. Produto rematadoview
The GENIUS KILO TX2 JL is a two-button remote control designed for gate and garage door opener systems. It operates on a frequency of 868.35 MHz, providing reliable communication with compatible receivers.
- Modelo: KILO TX2 JLC
- Frecuencia: 868.35 MHz
- Botóns: 2
- Compatibilidade: Compatible with GENIUS 868 systems and various gate opener remote controls including CASALI JA332, CASALI JA332 Grey, GENIUS JA332, GENIUS JA332 GREY, POWERDOOR JA332, POWERDOOR JA332 GREY, and GENIUS JA332 ORANGE.
- Receptores compatibles: JA335, 6100075, 6100146, 6100229, 6100230.
Figura 1: Fronte view of the GENIUS KILO TX2 JL remote control. This image displays the white remote with two distinct circular buttons and the 'GENIUS' brand name at the bottom.
Figura 2: Atrás view of the GENIUS KILO TX2 JL remote control. This image shows the reverse side of the remote, featuring the model number '6100332 (KILO TX2 JLC)', '868 MHz', 'Made In IE', and the 'CE 0470' marking.
3. Configuración
3.1. Instalación da batería
The GENIUS KILO TX2 JL remote control requires one CR2 battery. The remote is typically supplied with a battery already installed. If replacement is needed, follow these steps:
- Locate the battery compartment on the remote control. This is usually secured by small screws or a clip.
- Abra o compartimento con coidado usando un pequeno destornillador se é necesario.
- Retire a antiga batería CR2.
- Insert a new CR2 battery, ensuring the correct polarity (+ and -) is observed.
- Pecha o compartimento da batería de forma segura.
Nota: Elimina as baterías usadas de forma responsable segundo a normativa local.
3.2. Programación do control remoto
Programming the GENIUS KILO TX2 JL remote control involves linking it to your specific gate or garage door opener receiver. The exact programming procedure can vary depending on the model of your receiver.
General steps often include:
- Access the Receiver: Locate the programming button or switch on your gate or garage door opener's receiver unit. This unit is typically located near the motor.
- Activar o modo de aprendizaxe: Press and release the programming button on the receiver. An indicator light (LED) on the receiver will usually illuminate or flash, indicating it is in learning mode.
- Código de transmisión: Within a few seconds of activating learning mode, press and hold the desired button on your new GENIUS KILO TX2 JL remote control.
- Confirmar programación: The receiver's indicator light will typically change (e.g., flash rapidly, turn solid, or turn off) to confirm that the remote control has been successfully programmed.
- Proba de funcionamento: After programming, test the remote control by pressing the programmed button to ensure it operates your gate or garage door correctly.
Importante: Always refer to the instruction manual provided with your specific gate or garage door opener system for detailed and accurate programming instructions. If you are replacing an existing remote, some systems allow for cloning from an already programmed remote.
4. Instrucións de funcionamento
Once programmed, operating the GENIUS KILO TX2 JL remote control is straightforward:
- Apertura/Peche: Press the programmed button on the remote control once to activate your gate or garage door opener. Pressing it again will typically stop or reverse the operation, depending on your system's configuration.
- Rango: The remote has a maximum range of 10 meters. Ensure you are within this range for reliable operation. Environmental factors and obstacles can affect the effective range.
5. Mantemento
5.1. Substitución da batería
If the remote control's range decreases significantly or the indicator light (if present) does not illuminate when a button is pressed, the battery may need replacement. Refer to Section 3.1 for battery installation instructions. Use only CR2 alkaline batteries.
5.2. Limpeza
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water, as this can damage the internal components.
6 Solución de problemas
| Problema | Causa posible | Solución |
|---|---|---|
| O control remoto non funciona. | Dead or low battery. Incorrect programming. Out of range. | Replace the battery (CR2). Re-program the remote control (refer to Section 3.2). Move closer to the receiver. |
| Rango de funcionamento reducido. | Low battery. Interference from other devices. Obstructions. | Replace the battery. Check for sources of interference. Ensure a clear line of sight to the receiver if possible. |
| Gate/door opens intermittently. | Weak battery. Environmental factors. | Replace the battery. Ensure the remote is not exposed to extreme temperatures or moisture. |
If troubleshooting steps do not resolve the issue, contact your gate or garage door opener system installer or manufacturer for further assistance.
7. Especificacións
| Característica | Detalle |
|---|---|
| Marca | Xenio |
| Número de modelo | KILO TX2 JLC |
| Frecuencia | 868.35 MHz |
| Número de botóns | 2 |
| Tipo de batería | 1 x CR2 (Alkaline) |
| Rango máximo | 10 metros |
| Tecnoloxía de conectividade | Radiofrecuencia |
| Dispositivos compatibles | Genius 868 systems |
| Característica especial | Universal compatibility with listed models |
8. Garantía e soporte
Warranty information for the GENIUS KILO TX2 JL remote control is typically provided by the retailer or manufacturer at the time of purchase. Please retain your proof of purchase for warranty claims.
For technical support, programming assistance beyond the general steps provided, or warranty inquiries, please contact the authorized Genius dealer or the customer support department of your gate or garage door opener system manufacturer.
