Manual do usuario do inversor de onda sinusoidal pura COTEK SP-1500-112

1. Introdución

This manual provides essential information for the safe and efficient operation of your COTEK SP-1500-112 Pure Sine Wave Inverter. Please read this manual thoroughly before installation and use, and retain it for future reference. This inverter is designed to convert 12VDC battery power into 120VAC pure sine wave electricity, suitable for a wide range of sensitive electronic devices.

2. Información de seguridade

Always observe the following safety precautions to prevent injury or damage to the inverter or connected equipment.

Risco de descarga eléctrica: Non abra o inversor casing. Non hai pezas que o usuario poida reparar no interior. Encomende calquera mantemento a persoal cualificado.
Risco de incendio: Do not install the inverter in areas where flammable materials or gases are present. Ensure adequate ventilation.
Seguridade da batería: Work in a well-ventilated area when connecting batteries. Wear eye protection and gloves. Avoid short-circuiting battery terminals.
Conexión a terra adecuada: Asegúrese de que o inversor estea conectado a terra correctamente segundo as normas eléctricas locais.
Protección contra sobrecarga: Do not exceed the inverter's rated power output. Overloading can cause damage to the inverter and connected devices.

Image of a car battery with a recycling symbol, emphasizing battery safety.

This image illustrates the importance of battery safety, showing a car battery with a recycling symbol. Always handle batteries with care and ensure proper ventilation.

Image of a hard hat, safety glasses, and gloves, representing personal protective equipment.

This image depicts essential personal protective equipment including a hard hat, safety glasses, and gloves, highlighting the need for safety during installation and maintenance.

3. Características do produto

The COTEK SP-1500-112 inverter offers advanced features for reliable power conversion:

Saída de onda sinusoidal pura para electrónica sensible.
Power ON / OFF remote control capability (Green Terminal).
Input & output fully isolation for enhanced safety.
Temperature & load controlled cooling fan for optimal performance and noise reduction.
User friendly interface.
Type 1 Indoor Aluminum Enclosure for durability.
Adjustable power saving mode via variable resistor.
3-color LED status indicators for easy monitoring.
Comprehensive input/output protection: Reverse Polarity (Fuse) / Under Voltage / Over Voltage, Output protection: Short Circuit / Overload / Over Temperature.

COTEK SP-1500-112 Pure Sine Wave Inverter, angled view showing the blue casing and front panel.

This image displays the COTEK SP-1500-112 Pure Sine Wave Inverter from an angled perspective, highlighting its blue casing and the front panel with outlets and controls.

4. Configuración e instalación

Proper installation is crucial for the inverter's performance and safety. Follow these steps carefully:

4.1. Escolla dunha localización

Instale o inversor nunha zona fresca, seca e ben ventilada.
Evitar a luz solar directa, as fontes de calor e a humidade.
Ensure there is sufficient clearance around the inverter for airflow, especially around the cooling fan vents.
Mount the inverter securely on a stable surface.

4.2. Conexión de entrada de CC

Connect the inverter directly to a 12VDC battery bank. Use appropriately sized cables to minimize voltagcae.

Ensure the inverter's power switch is in the "OFF" position.
Connect the positive (+) DC cable from the battery to the positive (+) terminal on the inverter.
Connect the negative (-) DC cable from the battery to the negative (-) terminal on the inverter.
Tighten all connections securely to prevent loose contacts and arcing.

Traseira view of the COTEK SP-1500-112 inverter showing the DC input terminals.

This image shows the rear panel of the inverter, detailing the DC input terminals (red for positive, black for negative) and the chassis ground connection point.

4.3. Conexión de saída de CA

The inverter features dual GFCI 120VAC outlets for connecting your AC appliances.

Plug your AC appliances directly into the GFCI outlets on the inverter's front panel.
Ensure the total power consumption of all connected appliances does not exceed the inverter's rated output (1500W continuous).

Fronte view of the COTEK SP-1500-112 inverter showing the dual GFCI AC outlets.

This image displays the front panel of the inverter, clearly showing the two GFCI protected AC output receptacles, the power switch, and LED indicators.

4.4. Remote Control Connection (Optional)

The inverter supports an optional remote ON/OFF control via the green terminal block.

Connect a compatible remote switch or control system to the green terminal block as per the remote control's instructions.

5. Instrucións de funcionamento

5.1. Acendido do inversor

Ensure all DC and AC connections are secure.
Flip the main power switch on the inverter to the "ON" position.
Observe the LED indicators for status. A green LED typically indicates normal operation.

5.2. Understanding LED Indicators

The inverter features 3-color LED status indicators:

Verde: Funcionamento normal.
Amarelo/Ámbar: Warning condition (e.g., low battery voltage, high temperature). Refer to troubleshooting section.
Vermello: Fault condition (e.g., overload, short circuit, over temperature shutdown). The inverter will typically shut down.

5.3. Modo de aforro de enerxía

The inverter has an adjustable power saving mode. This mode reduces power consumption when no load or a very light load is detected. Consult the full technical datasheet for details on adjusting this setting via the variable resistor.

6. Mantemento

Un mantemento regular garante a lonxevidade e o rendemento óptimo do seu inversor.

Limpeza: Manteña o inversor limpo e libre de po e residuos. Use un pano seco para limpar o exterior. Non empregue produtos de limpeza líquidos.
Ventilación: Periodically check that the cooling fan vents are not obstructed. Ensure the fan operates freely.
Conexións: Annually inspect all DC and AC connections for tightness. Loose connections can cause overheating and poor performance.
Saúde da batería: Monitor your battery bank's health. A weak battery can cause the inverter to shut down prematurely due to low voltage.

7 Solución de problemas

Esta sección ofrece solucións a problemas comúns que podes atopar co teu inversor.

Problema	Causa posible	Solución
O inversor non se acende.	No DC input power; Loose battery connections; Blown DC fuse; Inverter switch OFF.	Comprobar vol. bateríatage; Tighten all DC connections; Replace fuse if necessary (refer to qualified technician); Ensure power switch is ON.
Inverter shuts down (Red LED).	Sobrecarga; Sobretemperatura; Batería baixatage; Short circuit on AC output.	Reduce connected load; Allow inverter to cool down; Recharge/replace battery; Disconnect AC load and check for short circuit.
No AC output (Green LED ON).	GFCI tripped; Faulty AC appliance; Loose AC connection.	Press GFCI reset button; Test appliance on another AC source; Check AC plug connection.
O ventilador de refrixeración non funciona.	No load or light load (fan is load/temperature controlled); Fan malfunction.	This is normal for light loads. If under heavy load and hot, contact support.

8. Especificacións

Detailed technical specifications for the COTEK SP-1500-112 Pure Sine Wave Inverter:

Parámetro	Valor
Nome do modelo	Serie SP-1500
Wattage	1500 vatios
Fonte de enerxía	Alimentado por batería
Marca	COTEK
Número de modelo do artigo	SP-1500-112
Dimensións do paquete	19.02 x 11.97 x 5.91 polgadas
Peso do elemento	11.76 libras
Garantía	2 anos de fabricante
Usos recomendados	Vehículo

Technical datasheet for COTEK SP-1500 series inverters, showing features and specifications.

This image presents the official technical datasheet for the COTEK SP-1500 series, detailing various models, electrical characteristics, protection features, environmental conditions, and certifications.

Mechanical drawings and dimensions for COTEK SP-1500 series inverters.

This image provides mechanical drawings and precise dimensions for the COTEK SP-1500 series inverters, useful for installation planning.

9. Garantía e soporte

The COTEK SP-1500-112 Pure Sine Wave Inverter comes with a 2 anos de garantía do fabricante.

For technical support, warranty claims, or service inquiries, please contact COTEK customer service. Refer to the official COTEK websitio web para obter a información de contacto máis actualizada.

Recoméndase rexistrar o produto ao mercalo para facilitar o servizo de garantía.

	Manual do usuario do inversor de onda sinusoidal pura da serie COTEK SP Manual de usuario completo para os inversores de onda sinusoidal pura da serie COTEK SP (SP-700 a SP-4000). Obtén información sobre a instalación, o funcionamento, a seguridade, as especificacións técnicas e as funcións avanzadas, como a saída de onda sinusoidal pura e a protección robusta.
	Manual do usuario do inversor de onda sinusoidal pura da serie COTEK SP Manual de usuario completo para os inversores de onda sinusoidal pura da serie COTEK SP (SP-700, SP-1000, SP-1500, SP-2000, SP-3000, SP-4000). Abarca as especificacións, a instalación, o funcionamento, a seguridade e a comunicación RS-232 para unha conversión de enerxía fiable.
	Manual do usuario do inversor de onda sinusoidal pura COTEK serie SK de 1500 W Manual de usuario completo para o inversor de onda sinusoidal pura COTEK serie SK de 1500 W, que abrangue a seguridade, as características, as especificacións, a instalación, o funcionamento, o mantemento e a resolución de problemas. Ofrece orientación detallada para o uso e o coidado axeitados.
	Manual do usuario do inversor de onda sinusoidal pura da serie COTEK SPT - SPT1200/2000/3000 Manual de usuario completo para os inversores de onda sinusoidal pura da serie COTEK SPT (SPT1200, SPT2000, SPT3000). Inclúe instrucións de seguridade, características funcionais, especificacións, instalación, mantemento, comunicación RS-485, resolución de problemas e información sobre a garantía.
	Inversor de onda sinusoidal pura da serie COTEK SPT con interruptor de transferencia: introdución e especificacións do produto Un resumo concisoview dos inversores de onda sinusoidal pura da serie COTEK SPT con interruptor de transferencia, que detalla as súas especificacións técnicas, o aspecto do produto, as pautas de instalación e a información de garantía para varios modelos.
	Manual do usuario do inversor de onda sinusoidal pura da serie COTEK SK Este manual do usuario ofrece instrucións completas para os inversores de onda sinusoidal pura da serie COTEK SK. Abarca información esencial de seguridade, características do produto, especificacións eléctricas e mecánicas detalladas, directrices de instalación, procedementos operativos, pasos para a resolución de problemas, consellos de mantemento e detalles da garantía para os modelos SK700, SK1000, SK1500, SK2000 e SK3000.

COTEK SP-1500-112