Introdución
This manual provides essential instructions for the proper installation, operation, and maintenance of the Armstrong 816032MF-000 Pump Bearing Assembly. Adhering to these guidelines will ensure optimal performance and longevity of the unit. Please read this manual thoroughly before proceeding with any procedures.
The Armstrong 816032MF-000 is a replacement bearing assembly designed for specific circulating pump models, including Bell & Gossett Series 60 (models 60-1 through 60-22) and BF Bearing Assembly for S55, S57, H51, H52, H53, H54 (BGP186863, BGP186864).
Información de seguridade
Always observe safety precautions when handling and installing pump components. Failure to do so may result in personal injury or equipment damage.
- Ensure the pump motor is stopped and power is disconnected before any lubrication, maintenance, or installation procedures.
- Usar equipos de protección individual (EPI) axeitados, como lentes e luvas de seguridade.
- Refer to the original pump's manual for specific disassembly and reassembly instructions.
- Do not over-oil or spill oil on resilient motor rings.
Produto rematadoview
The Armstrong 816032MF-000 is a critical component for maintaining the operational efficiency of compatible circulating pumps. This bearing assembly is manufactured from steel and weighs approximately 11.2 pounds.
Figura 1: Armstrong 816032MF-000 Pump Bearing Assembly. This image displays the complete bearing assembly, featuring a red base, a silver top plate, and a central shaft with a brass cap. The product label is visible on the side of the red base.
Características principais:
- Replacement bearing assembly for circulating pumps.
- Compatible with Bell & Gossett Series 60 (models 60-1 through 60-22).
- Also compatible with BF Bearing Assembly for S55, S57, H51, H52, H53, H54 (BGP186863, BGP186864).
- Constructed from durable steel.
- Country of Origin: Canada.
Configuración e instalación
Installation of the Armstrong 816032MF-000 Pump Bearing Assembly requires mechanical aptitude and adherence to safety protocols. It is recommended that installation be performed by qualified personnel.
- Preparación: Ensure the pump system is de-energized and isolated. Drain any fluid from the pump casing se é necesario.
- Acceso: Carefully disassemble the existing pump to access the old bearing assembly. Refer to your specific pump model's service manual for detailed disassembly instructions.
- Removal of Old Assembly: Remove the worn or damaged bearing assembly. Note the orientation and any shims or spacers for proper reassembly.
- Inspección: Inspect the pump housing and shaft for any damage or wear. Clean all mating surfaces thoroughly.
- Instalación da nova montaxe: Carefully install the new Armstrong 816032MF-000 bearing assembly. Ensure all components are seated correctly and fasteners are tightened to the manufacturer's specifications (refer to the pump's service manual for torque values).
- Remontaxe: Reassemble the pump components in reverse order of disassembly.
- Lubricación inicial: Before starting the pump, lubricate the new bearing assembly immediately with 1/2 oz. of the oil supplied or equivalent SAE30 non-detergent oil. Refer to the Maintenance section for detailed lubrication instructions.
Instrucións de funcionamento
Once the bearing assembly is installed and the pump is reassembled, follow the original pump manufacturer's operating procedures. The bearing assembly itself does not have specific operational controls, but its proper function is integral to the pump's operation.
- Ensure all connections are secure and leak-free before re-energizing the pump.
- Verify proper lubrication as per the Maintenance section.
- Monitor the pump during its initial operation for unusual noises, vibrations, or overheating, which could indicate an installation issue.
Mantemento
Regular lubrication is crucial for the longevity and performance of the Armstrong 816032MF-000 Pump Bearing Assembly. Adhere to the following lubrication instructions:
Figura 2: Close-up of the product label on the Armstrong 816032MF-000, displaying model number 816032-000 and detailed lubrication instructions. This label provides critical information regarding oil type and quantity.
Instrucións de lubricación:
- PRECAUCIÓN: Always stop the motor before performing any lubrication.
- Lubricación inicial: Lubricate the pump immediately after installation with 1/2 oz. of the oil supplied or equivalent.
- Seasonal Lubrication: At the start of each heating season, add 1/2 oz. of SAE30 non-detergent oil to the pump bracket oil cup.
- Importante: Stop adding oil if the cup fills before the specified amount is added. Do not over-oil or spill oil on resilient motor rings.
Resolución de problemas
This section addresses common issues related to the bearing assembly. For comprehensive pump troubleshooting, refer to the original pump manufacturer's manual.
| Problema | Causa posible | Solución |
|---|---|---|
| Excessive Noise/Vibration from Bearing Area | Insufficient lubrication, improper installation, worn bearings (if not a new assembly). | Check lubrication levels and apply as per Maintenance section. Re-check installation for proper seating and torque. If issue persists, inspect for damage. |
| Bearing Overheating | Lack of lubrication, excessive load, misalignment. | Ensure adequate lubrication. Verify pump alignment and operating conditions. |
| Oil Leakage from Bearing Assembly | Damaged seals, over-lubrication, improper assembly. | Inspect seals for damage and replace if necessary. Ensure correct oil quantity is used. Re-check assembly. |
Especificacións
- Número de modelo: 816032MF-000
- Número de peza: 816032MF-000
- Fabricante: Armstrong
- Material: Aceiro
- Peso do artigo: Aproximadamente 11.2 libras
- Dimensións do produto: Aproximadamente 1 x 2 x 3 polgadas
- Fonte de enerxía: AC/DC (relevant to the pump it's installed in)
- Cantidade do paquete do artigo: 1
- País de orixe: Canadá
- Bombas compatibles: Bell & Gossett Series 60 (60-1 to 60-22), BF Bearing Assembly for S55, S57, H51, H52, H53, H54 (BGP186863, BGP186864)
Garantía e Soporte
For warranty information and technical support regarding the Armstrong 816032MF-000 Pump Bearing Assembly, please contact Armstrong customer service or refer to the warranty documentation provided with your purchase. Keep your purchase receipt as proof of purchase.
For support related to the overall pump system, consult the original pump manufacturer's documentation.
