1. Produto rematadoview
The Yaskawa V1000 is a compact, high-performance AC microdrive designed for a wide range of industrial applications. It offers precise motor control, energy efficiency, and ease of use. This manual provides essential information for the safe and effective operation of your V1000 AC Drive.
Figura 1: Fronte view of the Yaskawa V1000 AC Drive (Model CIMR-VU2A0006FAA). This image shows the drive's compact design, control panel with display and buttons, and ventilation fins on the side.
2. Información de seguridade
WARNING: Risk of electric shock. Ensure power is disconnected before installation or maintenance.
Read this manual thoroughly before installing, operating, or performing maintenance on the V1000 AC Drive. Failure to follow these instructions may result in serious injury or equipment damage.
2.1 Precaucións xerais de seguridade
- Só o persoal cualificado debe instalar, operar e manter este equipo.
- Do not operate the drive with damaged cables or if the enclosure is open.
- Asegúrese dunha conexión a terra axeitada segundo as normas eléctricas locais.
- Comprobar o voltage matches the drive's specifications.
- Non toque os compoñentes internos inmediatamente despois de apagar a alimentación, xa que o volume residualtage may be present. Wait for the charge lamp to extinguish.
2.2 Consideracións ambientais
- Install the drive in a clean, dry, and well-ventilated area.
- Avoid direct sunlight, excessive dust, corrosive gases, and vibrations.
- Rango de temperatura de funcionamento: de 0 °C a 50 °C (de 32 °F a 122 °F).
3. Configuración
Proper installation and wiring are crucial for the safe and reliable operation of the V1000 AC Drive.
3.1 Montaxe
Mount the drive vertically on a flat, stable surface. Ensure adequate clearance for ventilation around the drive (minimum 50mm above and below, 25mm on sides).
3.2 Cableado
Refer to the wiring diagram provided in the full product manual for detailed connections. Key connections include:
- Power Input (R/L1, S/L2, T/L3): Connect the 3-phase 200-240V AC power supply.
- Saída do motor (U, V, W): Connect to the motor terminals.
- Terra (PE): Connect to a reliable earth ground.
- Terminais de control: For external control signals (e.g., run/stop, speed reference, fault output).
Always use appropriate wire gauges and circuit protection devices as specified in local electrical codes and the drive's technical specifications.
4. Operating the V1000 AC Drive
The V1000 drive can be operated via its integrated control panel or external control signals.
4.1 Panel de control rematadoview
O panel de control inclúe unha pantalla dixital e varios botóns:
- ESC: Escape/Back button.
- Frechas ARRIBA/ABAIXO: Navigate menus, adjust parameters.
- Frechas ESQUERDA/DEREITA: Shift cursor, change digits.
- ENTRAR: Confirm selection, enter parameter edit mode.
- CORRER: Start motor operation.
- PARAR: Stop motor operation.
4.2 Pasos básicos de funcionamento
- Encendido: Conecte a alimentación á unidade. A pantalla iluminarase.
- Configuración de parámetros: Configure essential parameters such as motor data (voltage, current, frequency), acceleration/deceleration times, and control mode (V/f, vector control). Refer to the parameter list in the detailed manual.
- Start Command: Preme o CORRER button on the control panel or activate the external run command.
- Axuste de velocidade: Adjust the motor speed using the UP/DOWN arrows (if in local control mode) or via external speed reference.
- Stop Command: Preme o PARA button or deactivate the external stop command.
5. Mantemento
Regular maintenance ensures the longevity and optimal performance of your V1000 AC Drive.
5.1 Comprobacións de rutina
- Diario: Check for unusual noises, vibrations, or odors. Verify display for error codes.
- Mensual: Inspect cooling fans for proper operation and cleanliness. Clean dust from ventilation openings.
- Anualmente: Check terminal connections for tightness. Inspect wiring for signs of wear or damage. Measure input/output voltages e correntes.
5.2 Limpeza
Use a soft, dry cloth to clean the exterior of the drive. For internal cleaning (only by qualified personnel with power disconnected), use compressed air to remove dust from heat sinks and circuit boards.
Always disconnect power and wait for the charge lamp to extinguish before performing any maintenance.
6 Solución de problemas
This section provides common issues and their potential solutions. For complex problems, consult a qualified technician or Yaskawa support.
| Problema | Causa posible | Solución |
|---|---|---|
| Drive does not power on. | No input power; Blown fuse. | Check power supply; Replace fuse (after identifying cause). |
| O motor non funciona. | No run command; Incorrect wiring; Motor fault. | Verify run command; Check motor and drive wiring; Inspect motor. |
| Overcurrent fault (OC). | Motor overload; Short circuit; Rapid acceleration. | Reduce load; Check motor/cables for shorts; Increase acceleration time. |
| Sobrevoltage fault (OV). | Volumen de entrada elevadotage; Rapid deceleration. | Comprobar o vol. de entradatage; Increase deceleration time; Install braking resistor if needed. |
7. Especificacións
Key technical specifications for the Yaskawa V1000 AC Drive (CIMR-VU2A0006FAA):
- Modelo: CIMR-VU2A0006FAA
- Serie: V1000 AC Drive
- Vol. De entradatage: 200-240V AC, 3-Phase
- Vol. De saídatage: 240 V CA
- Corrente de saída nominal: 6.0A (Heavy Duty) / 5.0A (Normal Duty)
- Potencia nominal do motor: 1 HP (0.75 kW)
- Fabricante: YASKAWA ELECTRIC
- Data de primeira dispoñibilidade: 14 de febreiro de 2025
8. Garantía e soporte
For detailed warranty information, please refer to the official Yaskawa warranty statement or contact your authorized Yaskawa distributor.
For technical support, service, or to obtain a full copy of the V1000 technical manual, please visit the official Yaskawa websitio ou póñase en contacto co seu departamento de atención ao cliente.
Yaskawa Electric Corporation
Websitio: www.yaskawa.com
