The Everbilt 1/6 HP Submersible Utility Pump (Model SUP54-HD) is designed for efficient water removal in various settings. This pump is ideal for use in most areas where unwanted water gathers, such as window wells, hot tubs, spas, and flooded basements. It can be totally submersed in water and is capable of pumping down to 3/8 inches from flat surfaces. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting.
Figura 1: Fronte view of the Everbilt 1/6 HP Plastic Utility Pump.
Información importante de seguridade
WARNING: To reduce the risk of electrical shock or injury, fully read and follow the instruction manual before attempting to install or operate this pump.
This pump should be installed in accordance with the National Electrical Code (NEC) and local codes and ordinances.
This pump should be connected to a 115V, GFCI outlet protected with a 5 AMP fusible ou interruptor automático.
The use of an extension cord to power this pump is NOT permitted.
Always unplug this pump when moving or servicing the pump and its installation.
Never pump flammable or explosive liquids. Only water should be pumped with this pump.
Always wear ANSI Z87.1 safety glasses when operating this pump.
Figura 2: Lateral view of the pump showing important warning and caution labels.
Instrucións de configuración
The Everbilt utility pump is designed for easy setup. Follow these steps to prepare your pump for operation:
Attaching a Garden Hose: Attach a 1-1/4 inch inside diameter or larger garden hose (not included) to the pump's outlet. Ensure a secure connection to prevent leaks.
Attaching a Smaller Hose (if preferred): If you prefer to use a smaller hose, attach the adapter (Part B) to the pump (Part A) outlet. Then securely attach the smaller hose to the adapter.
Colocación: Place the pump in the area where water needs to be removed. Ensure the pump is fully submerged in water before plugging it in. The pump is designed to drain water from flat surfaces down to 3/16 inches.
Figura 3: Arriba view of the pump illustrating the hose connection point.
For a visual guide on setup and operation, refer to the video below:
Video 1: Everbilt HP Plastic Utility Pump Review. This video demonstrates the pump's features and basic setup, including how to attach a hose and submerge the pump for operation.
Instrucións de funcionamento
Once the pump is properly set up and submerged, operating it is straightforward:
Submerxe a bomba: Ensure the pump is fully submerged in the water you wish to remove. The pump is designed to handle solids up to 1/8 inch in diameter, but avoid placing it directly in mud or areas with excessive debris to prevent clogging.
Conectar á enerxía: Plug the pump's 8-foot power cord into a 115V, GFCI protected outlet. The pump will begin operating automatically once plugged in. There is no on/off switch on the unit itself.
Monitor Discharge: Observe the water being discharged through the hose. The pump has a maximum flow rate of 28 gallons per minute and a maximum lifting height of 20 feet.
Desconexión: Once the desired water level is reached or the area is dry, unplug the pump from the electrical outlet.
See the pump in action in the following videos:
Video 2: "How fast does this work?" This video demonstrates the pump's powerful water removal capabilities in a pool setting.
Video 3: "No more water in the basement (Review)." This video showcases the pump's effectiveness in removing standing water from a basement, highlighting its ability to pump water close to the floor.
Mantemento
Regular maintenance ensures the longevity and optimal performance of your Everbilt utility pump:
Inspección de rutina: Periodically unplug the pump (making certain your hands are dry and you are not standing in water). Inspect the pump intake and remove any debris, such as leaves or small particles, that may have accumulated. Then plug the pump back into the grounded GFCI outlet.
Limpar atascos: If the pump becomes clogged with debris, follow these steps:
Desconecte a bomba da enerxía eléctrica.
Unscrew the screws (typically 6) and carefully remove the base plate.
Unscrew any additional screws (typically 4) and remove the impeller gasket.
Remove any debris around the shaft and impeller.
This pump contains cooling oil. Do NOT open the motor housing.
Resolución de problemas
If you encounter issues with your pump, refer to the common problems and solutions below:
Problema
Causa posible
Solución
Pump runs but only delivers a small amount of water.
Hose kinked or clogged; Impeller partially clogged; Air lock.
Check hose for kinks/clogs; Clean impeller; Tilt pump to release air.
O fusible funde ou o interruptor automático se dispara ao arrancar a bomba.
Motor overload; Incorrect fuse/breaker size; Impeller/shaft binding.
Check for motor obstruction; Ensure correct fuse/breaker; Clean impeller/shaft.
Motor runs for a short time, then stops.
Thermal overload protection activated; Low water level.
Allow pump to cool; Ensure sufficient water for continuous operation.
Especificacións
Característica
Detalle
Marca
Everbilt
Número de modelo
SUP54-HD
Caballos de forza
1/6 CV (0.17 CV)
Voltage
115 voltios
Caudal máximo
28 galóns por minuto (1680 GPH)
Altura máxima de elevación
20 pés
Dimensións do produto
9.06 cm de longo x 6.3 cm de ancho x 5.51 cm de alto
Peso do elemento
6.14 libras
Material
Plástico
Fonte de enerxía
AC/DC
Handles Solids Up To
1/8 inch diameter
Lonxitude do cable de alimentación
8 pés
Figure 4: Performance data and specifications for Everbilt utility pumps.
Garantía e Soporte
The Everbilt 1/6 HP Plastic Utility Pump comes with a Garantía limitada de 1 anos. For warranty claims or technical support, please contact the distributor:
Conserve o recibo de compra como proba de compra para calquera reclamación de garantía.
Documentos relacionados - SUP54-HD
Guía de instalación de accesorios de impermeabilización Everbilt Guía completa de instalación para accesorios de impermeabilización Everbilt, que detalla a preparación do subsolo, a creación de xuntas, o selado de esquinas e tubaxes e a aplicación final de tellas para instalacións impermeables.
Guía de uso e coidado da bomba de aspersor de céspede de plástico Everbilt Esta guía ofrece instrucións completas para a bomba de aspersor de céspede de plástico Everbilt, que abarcan a instalación, o funcionamento, as precaucións de seguridade, o mantemento e a resolución de problemas para os modelos EFLS10-HD, EFLS15-HD e EFLS20-HD.
Everbilt 1/2 HP Submersible Waterfall/Utility Pump (SUP80-HD) - Use and Care Guide Comprehensive use and care guide for the Everbilt 1/2 HP Submersible Waterfall/Utility Pump (Model SUP80-HD). Includes safety information, installation instructions, operation details, maintenance, and troubleshooting tips. Features automatic thermal protection and a one-year limited warranty.
