Manual do usuario do sistema de arranque remoto unidireccional e entrada sen chave Compustar CS920-S

1. Introdución

This manual provides essential information for the proper use, installation, and maintenance of your Compustar CS920-S 1-Way Remote Start and Keyless Entry System. Please read this document thoroughly before attempting any installation or operation to ensure optimal performance and safety. This system is designed to provide convenient remote starting and keyless entry for automatic transmission vehicles.

2. Produto rematadoview

The Compustar CS920-S system offers a reliable solution for remote vehicle control. It includes a CM900 control module and two 1-way remote controls with a maximum range of 1500 feet. Key features include remote start, keyless entry, and trunk pop output.

Compustar CS920-S system components including box, remotes, control module, antenna, and wiring harnesses.

Figure 2.1: Complete Compustar CS920-S system package with all included components.

2.1. Compoñentes do sistema

CM900 Control Module: The central processing unit for the remote start and keyless entry functions.
Two 1-Way 4-Button LED Remotes: Used to send commands to the vehicle.
Antena: Receives signals from the remote controls.
Arneses de cableado: For connecting the system to the vehicle's electrical components.
Interruptor de alternancia: For system control or valet mode.

Close-up of two Compustar 1-way 4-button remote controls.

Figure 2.2: The two 1-way 4-button remote controls included with the CS920-S system.

3. Configuración e instalación

Professional installation is highly recommended for this product. Improper installation can lead to vehicle damage or system malfunction. Some vehicles may require additional parts, such as an immobilizer bypass module (e.g., BLADE-AL or ADS-ALCA), which are sold separately.

3.1. Consideracións previas á instalación

This system is designed for automatic transmission vehicles only.
Verify vehicle compatibility and identify any necessary bypass modules or additional wiring components.
Ensure all vehicle power is disconnected before beginning installation.

3.2. CM900 Control Module Wiring Schematic

The CM900 module requires precise wiring connections to your vehicle's electrical system. Refer to the schematic below for connection points. Consult a professional installer or vehicle-specific wiring diagrams for accurate identification of vehicle wires.

Wiring schematic for the Compustar CM-900 remote start control module, showing main harness, blade harness, lock connector, and various ports like antenna, temp sensor, and RS232.

Figure 3.1: CM-900 Wiring Schematic (Remote Start).

3.3. Immobilizer Bypass (If Required)

Many modern vehicles are equipped with an immobilizer system that prevents the engine from starting without the correct key. For remote start functionality, an immobilizer bypass module is often required. The CM900 module has a dedicated slot for a BLADE-AL module or can interface with other bypass modules like ADS-ALCA.

Compustar CM900 module with an arrow indicating where the BLADE-AL module inserts.

Figure 3.2: CM900 module showing the BLADE-AL slot (BLADE-AL sold separately).

Packaging for the iDatalink BLADE-AL immobilizer bypass module.

Packaging for the iDatalink ADS-ALCA remote start and databus interface module.

Figura 3.3: Examples of compatible immobilizer bypass modules (BLADE-AL and ADS-ALCA).

4. Instrucións de funcionamento

The CS920-S system uses a 1-way remote control. This means the remote sends commands to the vehicle, but the vehicle does not send confirmation back to the remote. The remote's LED will illuminate solid blue when a button is pressed.

4.1. Funcións de control remoto

Close-up of two Compustar 1-way 4-button remote controls, showing lock, unlock, trunk, and remote start buttons.

Figure 4.1: Compustar 1-Way Remote Control Layout.

Botón de bloqueo (🔒): Press once to lock the vehicle doors. The remote's LED will illuminate.
Botón de desbloqueo (🔓): Press once to unlock the vehicle doors. The remote's LED will illuminate.
Remote Start Button (✱): Press and hold for approximately 2.5 seconds to remote start the vehicle. The vehicle's parking lights will flash to indicate successful remote start.
Trunk Pop Button (🚗): Press and hold for approximately 2.5 seconds to open the vehicle's trunk (if wired to the system).

4.2. Funcionamento de arranque remoto

Ensure the vehicle is in Park and the parking brake is engaged (if applicable).
Press and hold the Remote Start button (✱) on your remote for 2.5 seconds.
The vehicle will start, and the parking lights will turn on and remain on for the duration of the remote start cycle.
To turn off the vehicle during a remote start cycle, press and hold the Remote Start button (✱) de novo durante 2.5 segundos.

4.3. Entering the Vehicle After Remote Start

Unlock the vehicle doors using the Unlock button (🔓) no teu control remoto.
Enter the vehicle. Do not press the brake pedal yet.
Insert your key into the ignition and turn it to the 'ON' or 'RUN' position (do not turn to 'START').
Press the brake pedal. The remote start system will disengage, and the vehicle will now be operating under key control.

5. Mantemento

5.1. Substitución da batería do control remoto

If the range of your remote control decreases significantly or the LED indicator fails to illuminate, the battery may need replacement. Refer to the remote control's specific instructions for battery type and replacement procedure. Typically, this involves opening the remote casing and replacing the coin-cell battery.

5.2. System Care

Keep the control module and antenna free from moisture and extreme temperatures.
Avoid dropping the remote controls or exposing them to water.
Regularly check wiring connections for any signs of wear or corrosion, especially if the system was self-installed.

6 Solución de problemas

This section addresses common issues you might encounter with your Compustar CS920-S system.

Problema	Causa posible	Solución
Remote start fails to activate.	Vehicle not in Park, hood pin switch open, low battery, immobilizer issue, programming error.	Ensure vehicle is in Park. Check hood pin switch. Replace remote battery. Consult installer for immobilizer or programming check.
Alcance remoto reducido.	Low remote battery, environmental interference, antenna obstruction.	Replace remote battery. Move away from sources of interference (e.g., power lines, large buildings). Ensure antenna is not obstructed.
As portas non se pechan/abren.	Wiring issue, remote battery low, system in valet mode.	Check remote battery. Verify system is not in valet mode. Consult installer to check wiring.
System requires programming for specific features (e.g., diesel engine delay).	Default settings may not match vehicle requirements.	Programming requires specialized tools like the Compustar OP-500 or iDatalink ADS-USB interface. This should be performed by a professional installer.

7. Especificacións

Modelo: CS920-S (920S)
Tipo de mando a distancia: 1-Way, 4-Button LED
Rango máximo: 1500 pés
Módulo de control: CM900
Compatibilidade: Automatic Transmission Vehicles Only
Peso do artigo: 1.52 libras
Dimensións do paquete: 8.04 x 5.09 x 3.45 polgadas
Fabricante: Compustar
ASIN: B077NDP76T
Data de primeira dispoñibilidade: 21 de novembro de 2017

8. Garantía e soporte

Compustar products are covered by a manufacturer's warranty. For specific warranty details, including coverage period and terms, please refer to the documentation provided with your product or visit the official Compustar website. For technical support, installation assistance, or warranty claims, please contact your authorized Compustar dealer or the Compustar customer service directly.

Nota: Unauthorized installation or modification of the system may void the product warranty.

	Manual do usuario de CompuStar Pro 2BSHLEDR - Firstech LLC Manual de usuario para o sistema de arranque remoto con LED de 2 vías e 2 botóns CompuStar Pro 2BSHLEDR de Firstech LLC. Abarca a instalación, o funcionamento, as funcións, a programación e a garantía.
	Guía de inicio rápido do Compustar 2WSSR-T11: Funcións e funcionamento do control remoto Unha guía concisa para o funcionamento do sistema de arranque remoto e entrada sen chave Compustar 2WSSR-T11, que detalla as funcións dos botóns, as opcións do menú, a carga da batería e información importante de seguridade.
	Guía do produto e instalación do arrancador remoto Compustar RS1B-DC3 Guía completa do produto para o arrancador remoto Compustar RS1B-DC3. Obtén información sobre a instalación, os procedementos de programación, o diagnóstico e a resolución de problemas do teu vehículo.
	Firstech Compustar 1WS2R-AF ANT-1WAF Guía de inicio rápido Guía de inicio rápido para os sistemas de arranque remoto e seguridade Firstech Compustar, que abrangue o control remoto 1WS2R-AF e o módulo de antena ANT-1WAF. Inclúe a conformidade coa FCC/IC, as funcións dos botóns, as características do control remoto, os indicadores LED e as notas de instalación.
	Guía de inicio rápido do sistema de arranque remoto Compustar RF-2WR3R-FM Unha guía concisa para o funcionamento do sistema de arranque remoto Compustar RF-2WR3R-FM, incluíndo as funcións dos botóns, os indicadores LED e a resolución de problemas cos códigos de erro.
	Compustar RF-1WR3R-FM Remote Start Quick Start Guide Quick start guide for the Compustar RF-1WR3R-FM remote car starter and alarm system. Learn basic functions like locking/unlocking doors, remote starting, Valet Mode, and understanding alarm/start error codes.

Compustar CS920-S