Introdución
Thank you for choosing the Sunco LED Wraparound Shop Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before installation and retain them for future reference.
Información de seguridade
- AVISO: Risco de descarga eléctrica. Desconecte a alimentación no fusible ou no disyuntor antes da instalación ou do mantemento.
- Este produto debe ser instalado de acordo co código de instalación aplicable por unha persoa familiarizada coa construción e o funcionamento do produto e os perigos implicados.
- Asegurar a subministración voltage é compatible coa luminaria (120-277 V).
- Do not handle live wires.
- Non modifiques o aparello. Calquera modificación pode anular a garantía e crear riscos para a seguridade.
- Apto para damp localizacións.
Contido do paquete
Comprobe que todos os compoñentes estean presentes antes de comezar a instalación:
- LED Wraparound Shop Light Fixture (2 units for 2-pack)
- Hardware de montaxe
- Linking Cables (for connecting multiple fixtures)
- Manual de instrucións
Especificacións
| Número de modelo | SHW-40W-5K-2PK |
| Consumo de enerxía | 40 vatios |
| Saída de luz | 3500 lúmenes |
| Temperatura da cor | 5000K de luz do día |
| Voltage | 120-277 V |
| Dimensións | 48 cm de longo x 2.36 cm de ancho x 5.35 cm de alto |
| Ángulo do feixe | 110 graos |
| CRI | 80+ |
| Tipo de instalación | Flush Mount / Hardwired |
| Características especiais | Prismatic Lens, Linkable (up to 8 units), Non-Dimmable |
| Certificacións | ETL |
Instrucións de instalación
This fixture is designed for direct surface mounting to the ceiling. Always ensure power is disconnected before starting installation.
- Prepare o dispositivo: Carefully remove the diffuser (Part B) from the lamp base (Part A) to access the wiring and mounting points.
- Montar o aparello: Coloque a lamp base against the ceiling where you intend to install it. Mark the mounting holes. Use appropriate mounting hardware (screws, anchors) to securely attach the lamp base to the ceiling.
- Cableado: Bring the electrical supply wires from the junction box to the fixture. Connect the wires according to local electrical codes: Black to Black (Live), White to White (Neutral), Green/Bare Copper to Green (Ground). Ensure all connections are secure with wire nuts.
- Replace Diffuser: Once wiring is complete and secure, carefully reattach the diffuser to the lamp base. Ensure it snaps firmly into place along both sides.
Linking Multiple Fixtures
These fixtures are linkable, allowing you to connect up to 8 units from a single power source. Use the provided linking cables or flush linking connectors to connect fixtures end-to-end. Ensure the total wattage of linked fixtures does not exceed the circuit's capacity.
Operación
Once properly installed and powered, the Sunco LED Wraparound Shop Light will provide instant-on, flicker-free illumination. This fixture is non-dimmable and operates at a 5000K Daylight color temperature, designed to mimic natural daylight for enhanced visibility and alertness.
Mantemento
The Sunco LED Wraparound Shop Light is designed for long-lasting performance with minimal maintenance. The integrated LED design means there are no bulbs to replace.
- Limpeza: Ensure power is off before cleaning. Wipe the fixture and diffuser with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or optical components.
- Inspección: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and contact a qualified electrician or Sunco Lighting support.
Resolución de problemas
If you experience issues with your Sunco LED Wraparound Shop Light, refer to the following common problems and solutions:
| Problema | Causa posible | Solución |
|---|---|---|
| A luz non se acende | Sen subministración eléctrica; Cableado solto; Aparello defectuoso. | Check circuit breaker/fuse. Ensure all wire connections are secure. If problem persists, contact Sunco support. |
| A luz é débil ou parpadea | Incompatible dimmer switch (fixture is non-dimmable); Loose wiring; Power fluctuation; Fixture nearing end of life. | Ensure no dimmer switch is used. Check wiring connections. If dimming occurs after extended use (e.g., 1.5-2 years), it may indicate a component issue. Contact Sunco support for warranty assistance. |
| Only some linked lights are working | Loose linking cable connection; Faulty individual fixture in the chain. | Check all linking cable connections. Isolate the non-working fixture to determine if it's an individual unit issue. |
Se os pasos de resolución de problemas non resolven o problema, póñase en contacto co servizo de atención ao cliente de Sunco Lighting.
Garantía e Soporte
Sunco Lighting stands behind the quality of its products. This LED Wraparound Shop Light comes with a Protección de 7 ano warranty. For warranty claims, technical assistance, or any questions regarding your product, please contact our knowledgeable support specialists.
Información de contacto: Please refer to the Sunco Lighting websitio web ou na documentación da súa compra para obter os datos de contacto máis actuais.
