1. Introdución
The BWT Perla One 11433 Water Softener is designed to effectively reduce limescale in your drinking water system, contributing to improved well-being and preserving the value of your home appliances and sanitary installations. This model is suitable for areas with moderately hard water and for installations preceding a water heater, catering to low demands.
By installing the Perla One, you can significantly extend the lifespan of water-carrying household appliances, reduce maintenance requirements, and lower energy consumption. A mere two-millimeter layer of limescale on heating surfaces can increase energy consumption by up to 20%.
Beneficios clave:
- Noticeably soft skin and supple, shiny hair.
- Cozy and soft laundry.
- Fewer limescale deposits on faucets, tiles, and pipe installations.
- Sparkling glasses and shiny dishes.
- Increased lifespan of household appliances.
- Up to 50% less consumption of detergents, cleaning agents, and washing-up liquids.
- Reduced energy and heating costs.
2. Información de seguridade
Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or improper operation of the device.
- Instalación profesional: A instalación debe ser realizada por un profesional cualificado de acordo coas normas locais de fontanería e electricidade.
- Presión da auga: Ensure the water pressure in your home is within the operating limits specified for the device.
- Seguridade eléctrica: If electrical connections are required, ensure they are made by a qualified electrician and comply with all local regulations. Disconnect power before servicing.
- Manipulación de produtos químicos: Use only BWT-approved regeneration salt. Avoid contact with eyes and skin. Store salt in a dry, cool place, out of reach of children and pets.
- Detección de fugas: Regularly inspect the system for any signs of leaks. Address any leaks immediately to prevent water damage.
- Nenos e animais: Keep children and pets away from the water softener, especially during regeneration cycles or when handling salt.
3. Contido do paquete
Verifique que todos os compoñentes que se indican a continuación estean presentes no seu paquete:
- 1 x BWT Perla One Water Softener System
- 1 x Multiblock X DN 32
- 1 x Connection Kit DN 32/32 DVGW
- 1 x AQA Hardness Tester
- 1 x 2m Flush Hose
- 1 x 2m Overflow Hose (18 x 24 mm)
- 1 x Mounting Material
- 1 x BWT Siphon
Image 1: BWT Perla One Water Softener System. This image shows the compact, white and blue exterior of the BWT Perla One water softener.
Image 2: Multiblock X DN 32 and Connection Kit. This image displays the brass valve assembly with a green handle and additional connection pieces, part of the included connection kit.
Image 3: Flexible Hoses. Two flexible metal hoses with threaded connectors are shown, used for connecting the water softener to the main water supply.
Image 4: BWT Siphon and Overflow Hose Component. This image shows a white plastic siphon component with a grey pipe extension, used for drainage.
Image 5: Mounting Material. Various mounting components including metal clamps, screws, wall plugs, and rubber washers are displayed.
Image 6: AQA Hardness Tester Kit. This image shows a small test tube and two dropper bottles, labeled 'AQA test solution A' and 'B', used for measuring water hardness.
4. Configuración
The BWT Perla One water softener is designed for standalone installation. It is recommended that installation be carried out by a certified plumber.
4.1. Escolla dunha localización para a instalación
- Select a dry, level, and frost-free location near the main water supply inlet.
- Ensure adequate space for maintenance, salt replenishment, and access to connections.
- The location must have access to a suitable drain for the regeneration wastewater.
4.2. Connecting to Water Supply
- Shut off the main water supply to your home.
- Install the Multiblock X DN 32 and the Connection Kit DN 32/32 DVGW according to the provided diagrams (not included in this manual, refer to separate installation guide).
- Connect the water softener's inlet and outlet to the plumbing system using the flexible hoses. Ensure all connections are secure and watertight.
4.3. Drain and Overflow Connections
- Connect the 2m Flush Hose and the 2m Overflow Hose (18 x 24 mm) to the designated ports on the softener.
- Route these hoses to a suitable drain, ensuring there is an air gap to prevent back-siphonage. Install the BWT Siphon as per local regulations.
4.4. Adding Regeneration Salt
- Open the lid of the water softener.
- Fill the storage tank with BWT-approved regeneration salt. The tank can hold up to 32 kg of salt.
- Pecha a tapa de forma segura.
Image 7: BWT Perla One with lid open. This image shows the water softener with its top lid open, revealing the internal brine tank where regeneration salt is added.
4.5. Initial Startup and Programming
- Slowly open the main water supply valve to allow water to fill the softener. Check for leaks.
- Plug in the power cord (if applicable). The microprocessor control will guide you through the initial setup.
- Use the AQA Hardness Tester to determine your incoming water hardness.
- Program the water softener with your specific water hardness settings using the control panel. Refer to the separate programming guide for detailed instructions.
- Initiate a manual regeneration cycle to flush the system and prepare it for operation.
5. En funcionamento
The BWT Perla One operates automatically once properly set up. It uses AQA Perla technology with microprocessor control for efficient and easy operation.
5.1. Automatic Softening
The system continuously monitors water usage and automatically initiates regeneration cycles as needed. It offers 24 hours of soft water operation for 1 to 2 residential units.
5.2. Regeneration Process
During regeneration, the softener flushes the resin bed with a brine solution to remove accumulated hardness minerals. This process is typically scheduled for times of low water usage (e.g., late at night) to minimize inconvenience. The intelligent regeneration system ensures economical use of salt and rinse water.
5.3. Monitoring Salt Levels
Regularly check the salt level in the brine tank. When the salt level is low, replenish it with BWT-approved regeneration salt to ensure continuous soft water supply. The system may provide an indicator for low salt levels.
6. Mantemento
Regular maintenance ensures the longevity and optimal performance of your BWT Perla One water softener.
6.1. Salt Replenishment
As mentioned in the operating section, regularly check and replenish the salt in the brine tank. It is recommended to keep the tank at least one-quarter full. Use only high-quality water softener salt.
6.2. Brine Tank Cleaning
Periodically (e.g., once a year), inspect and clean the brine tank. This involves removing any salt crusts or sediment that may accumulate at the bottom. Refer to the detailed cleaning instructions in the full product manual.
6.3. System Inspection
Annually, inspect all connections, hoses, and valves for any signs of wear, corrosion, or leaks. Ensure the drain line is clear and free of obstructions. If any issues are found, contact a qualified service technician.
6.4. Resin Bed Maintenance
While the resin bed is designed for long-term use, certain conditions (e.g., high iron content in water) may require specialized cleaning or replacement over time. Consult a professional if you suspect issues with the resin bed.
7 Solución de problemas
This section provides solutions to common issues you might encounter with your BWT Perla One water softener.
| Problema | Causa posible | Solución |
|---|---|---|
| Water is not soft | Baixo nivel de sal Incorrect hardness setting System bypassed Poder outage | Engade sal ao tanque de salmoira Check and adjust hardness setting Ensure bypass valve is in service position Check power supply and reset time/settings |
| Excessive salt consumption | Incorrect hardness setting Frequent regeneration cycles | Verify and adjust hardness setting Consult manual for regeneration frequency adjustment or contact support |
| Baixa presión da auga | Clogged pre-filter (if installed) Resin bed issues Partially closed bypass valve | Clean or replace pre-filter Contacte co técnico de servizo Ensure bypass valve is fully open in service position |
| Water in brine tank is too high | Liña de drenaxe obstruída Interruptor flotante mal funcionando | Clear drain line obstruction Contacte co técnico de servizo |
If you encounter a problem not listed here or if the suggested solutions do not resolve the issue, please contact BWT customer support or a qualified service technician.
8. Especificacións
| Marca | BWT |
| Nome do modelo | 11433 |
| Número de modelo do artigo | 11433 |
| Característica especial | Microprocessor control for easy operation |
| Material | Perla |
| Tipo de instalación | Autónomo |
| Método de purificación | Intercambio iónico |
| Maximum TDS Level Supported (PPM) | 300 |
| Compoñentes incluídos | BWT Perla One Water Softener System, Multiblock X DN 32, Connection Kit DN 32/32 DVGW, AQA Hardness Tester, 2m Flush Hose, 2m Overflow Hose 18 x 24 mm, Mounting Material, BWT Siphon |
| Dispoñibilidade de Recambios | Información non dispoñible |
| ASIN | B0854LLHXM |
| Código Internacional do Artigo | 04050808114337 |
| Data de primeira dispoñibilidade en Amazon.com.be | 11 de xuño de 2022 |
9. Garantía e soporte
For warranty information, please refer to the documentation provided with your purchase or contact BWT customer service directly. Details regarding spare parts availability are not provided in the product specifications.
For technical support, service, or to inquire about spare parts, please contact your local BWT distributor or visit the official BWT website. Keep your purchase receipt and model number (11433) handy when contacting support.
