Jandy R0693900 TruClear Salt Cell Assembly Instruction Manual

1. Introdución

This manual provides detailed instructions for the installation, operation, and maintenance of your Jandy R0693900 TruClear Salt Cell Assembly. Please read this manual thoroughly before attempting any procedures to ensure safe and efficient use of the product.

2. Información importante de seguridade

• Always disconnect power to the pool equipment at the main breaker before performing any service or maintenance.
• Wear appropriate personal protective equipment, including safety glasses and gloves, when handling pool chemicals or performing maintenance.
• Do not use undiluted muriatic acid for cleaning the salt cell, as this can cause severe damage to the cell and void the warranty. Always follow manufacturer guidelines for chemical dilution and handling.
• Asegúrate de que todas as conexións de fontanería estean seguras e estancas para evitar fugas.

3. Produto rematadoview

The Jandy R0693900 TruClear Salt Cell Assembly is a replacement component for Jandy Pro Series TruClear Chlorinators, designed to generate chlorine for your pool from salt. This assembly includes the cell and its integrated power cable.

Figure 1: Jandy R0693900 TruClear Salt Cell Assembly, showing the cell body and coiled power cable.

4. Instrucións de instalación

Replacing the Jandy TruClear Salt Cell Assembly is a straightforward process. Follow these steps carefully:

4.1. Step 1: Disconnect Power

Before beginning any work, ensure the pool pump and all associated electrical components are turned off at the main circuit breaker. This prevents accidental startup and electrical hazards.

4.2. Step 2: Drain Water

Open the air relief valve at the top of your pool filter to allow water to drain from the system. This will lower the water level in the plumbing, preventing water from spilling when the salt cell is removed.

4.3. Step 3: Remove Old Salt Cell

Locate the existing salt cell in your pool's plumbing system. The cell is typically installed in-line with the return plumbing to the pool. Unscrew the locking ring that secures the cell to the plumbing. Carefully lift the old salt cell assembly out of its housing. Disconnect the power cable from the control box.

Figure 2: The existing Jandy salt cell integrated into the pool's plumbing system.

Imaxe 3: Primeiro plano view of the electrical connector for the Jandy salt cell, which needs to be disconnected from the control box.

4.4. Step 4: Install New Salt Cell

Insert the new Jandy R0693900 TruClear Salt Cell Assembly into the plumbing housing. Ensure the flow arrows on the cell align with the direction of water flow in your plumbing. Tighten the locking ring securely to prevent leaks. Connect the power cable of the new cell to the Jandy TruClear control box.

Figure 4: The new Jandy R0693900 salt cell assembly, ready for installation, showing the integrated cable.

Figura 5: Arriba view of the salt cell, highlighting the flow indicators for correct orientation during installation.

4.5. Step 5: Restore Power and Check Operation

Close the air relief valve on the filter. Restore power to the pool pump and control box at the main circuit breaker. Turn on the pool pump. Verify that the Jandy TruClear control box indicates

Documentos relacionados - R0693900

	Substitución da cela TruClear de Jandy: Guía de instalación de pezas de reposto Instrucións oficiais de instalación para a batería de recambio Jandy TruClear (peza R0693900) para sistemas de piscina Jandy Pro Series. Inclúe avisos de seguridade, contido do paquete e procedementos de instalación paso a paso.
	Manual de instalación e funcionamento do dispositivo xerador de cloro Jandy AquaPure Ei Series APURE35PLG Manual completo de instalación e funcionamento para o dispositivo xerador de cloro enchufable Jandy AquaPure Ei Series APURE35PLG de 120 V. Abarca a seguridade, a descrición do sistema, a instalación, a preparación da auga, o funcionamento, o mantemento e a resolución de problemas.
	Bombas e quentadores de gas Jandy VS: Guía de substitución directa A comprehensive guide from Jandy for pool professionals and homeowners on replacing existing pool pumps and gas heaters with Jandy VS FloPro pumps and JXi heaters. Features include easy installation, performance benefits, technical specifications, and comparison charts with Pentair and Hayward models.
	Manual de instalación dos sistemas de control Jandy AquaLink RS con todos os botóns e un só toque Guía de instalación completa para os sistemas de control Jandy AquaLink RS, que abrangue os modelos All Button e OneTouch. Este manual ofrece instrucións detalladas para a configuración, o cableado, a programación e a resolución de problemas dos equipos de automatización de piscinas e spas.
	Guía de instalación do soprador de aire para piscinas e spas Jandy Pro Series Guía de instalación detallada para os sopradores de aire para piscinas e spas Jandy Pro Series (modelos PSB110, PSB115, PSB120, PSB210, PSB215, PSB220). Abarca as precaucións de seguridade esenciais, os cálculos de tamaño dos sopradores, as configuracións de fontanería (estándar, de longo percorrido, baixo rasante, bucle Hartford) e as instrucións de cableado eléctrico para un funcionamento seguro e eficaz.
	Clorador de sal comercial Jandy: Manual de instalación e funcionamento Guía completa para a instalación, o funcionamento e o mantemento dos cloradores de sal comerciais Jandy (modelos JSWC40, JSWC53, JSWC80, JSWC100). Abarca a seguridade, a descrición do sistema, a instalación, o funcionamento, o mantemento e a resolución de problemas.