Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope

Introdución

This manual provides essential information for the safe and efficient operation of your Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope. This instrument is designed for precise measurement and analysis of electronic signals, featuring a 100 MHz bandwidth and 2 analog channels.

As características principais inclúen:

• Analog input channels: 2 inputs
• Ancho de banda: 100 MHz
• Sample rate: 2.5 GS/s Half channels; 1.25 GS/s All channels
• Record length: 10 Mpoints per channel
• Vertical resolution: 8 bits ADC; Up to 16 bits in high-resolution mode

Configuración e conexións

Before operating the oscilloscope, ensure it is placed on a stable, level surface with adequate ventilation. Connect the power cord to the instrument and a grounded AC outlet.

Figure 1: Front panel of the Tektronix MSO22 2-BW-100 Oscilloscope, showing the display, control knobs, buttons, and input connectors (Inputs 1, 2, Aux In, AFG/Aux Out).

Conexións de entrada

• Analog Inputs (1, 2): Connect your probes to these BNC connectors for signal acquisition.
• Entrada auxiliar: Auxiliary input for external trigger or other signals.
• AFG/Aux Out: Output for the Arbitrary Function Generator or auxiliary signals.

Encender

Press the power button located on the front panel to turn on the instrument. Allow a few moments for the system to boot up.

Instrucións de funcionamento

This section outlines the basic steps for operating the oscilloscope to capture and analyze waveforms.

Basic Waveform Capture

1. Conectar a sonda: Attach a compensated probe to one of the analog input channels (e.g., Input 1).
2. Conectar ao circuíto: Connect the probe tip to the test point in your circuit and the ground clip to the circuit's ground.
3. Configuración automática: Preme o Auto-Set button (if available, common on oscilloscopes) to automatically adjust vertical and horizontal settings for a stable display.
4. Adjust Vertical Scale: Usa o Escala Vertical knob to adjust the volts per division, controlling the amplitude of the waveform on the screen.
5. Adjust Horizontal Scale: Usa o Escala Horizontal knob to adjust the seconds per division, controlling the time base of the waveform.
6. Adjust Trigger: Usa o Nivel de disparo knob to set the voltage level at which the oscilloscope captures the waveform, ensuring a stable display.

Funcións de medición

The MSO22 2-BW-100 offers various automated measurement functions. Access these through the on-screen menu system. Common measurements include Peak-to-Peak Voltage, Frequency, Period, and Rise/Fall Time.

Mantemento

Un mantemento axeitado garante a lonxevidade e a precisión do seu osciloscopio.

Limpeza

• Limpe as superficies exteriores cun suave, damp pano. Non use produtos de limpeza ou disolventes abrasivos.
• Asegúrese de que non entre líquido no instrumento.
• Clean the display screen with a soft, lint-free cloth specifically designed for electronic displays.

Calibración

For optimal performance, periodic calibration by qualified service personnel is recommended. Refer to the official Tektronix service manual for calibration procedures and intervals.

Resolución de problemas

Esta sección ofrece solucións a problemas comúns cos que podes atoparte.

• Sen visualización:
  • Ensure the power cord is securely connected and the instrument is powered on.
  • Check the brightness and contrast settings of the display.
• Unstable Waveform:
  • Adjust the trigger level and trigger source settings.
  • Verify the probe compensation is correct.
  • Check for proper grounding of the probe and the circuit under test.
• Non se detectou sinal:
  • Ensure the probe is correctly connected to the input channel and the circuit.
  • Check the input coupling (AC/DC/GND) and vertical scale settings.
  • Verify the signal source is active.

If problems persist, contact Tektronix customer support.

Especificacións

Detailed technical specifications for the Tektronix MSO22 2-BW-100 Mixed Signal Oscilloscope.

Garantía e Soporte

Tektronix products are designed for reliability and performance. For information regarding product warranty, please refer to the warranty statement included with your purchase or visit the official Tektronix websitio.

For technical support, service, or additional documentation, please contact Tektronix customer service or visit their official support portal. Ensure you have your product model number (MSO22 2-BW-100) and serial number ready when contacting support.

Recursos en liña: www.tek.com