1. Introdución
This manual provides detailed instructions for the installation, operation, and maintenance of the LevelOne FCS-5202 Gemini 4 MP Fixed IP Camera. The FCS-5202 is an outdoor fixed camera designed for reliable and cost-effective IP surveillance networks. It is built to withstand various environmental conditions, including rain, extreme heat, snow, dust, and humidity. This camera delivers clear 4-megapixel resolution images and supports 802.3af Power over Ethernet (PoE) for combined power and data transmission over a single Cat.5 cable.
2. Produto rematadoview
2.1 Características principais
- 4 Megapixel High-Definition Resolution for clear and sharp images.
- Supports H.264, H.265, and MJPEG video compression for efficient storage and streaming.
- Integrated 802.3af Power over Ethernet (PoE) for simplified installation with a single cable.
- IP67 Weather-Resistant Casing ensures durability in outdoor environments.
- Advanced Motion Detection capabilities, including intrusion, camera tampering, and line crossing detection.
- Event notification support for immediate alerts.
2.2 Contido do paquete
- LevelOne FCS-5202 IP Camera
- Guía de instalación (consulte este manual)
- Accesorios de montaxe
2.3 Diagrama da cámara
Figura 1: Fronte e lateral view of the LevelOne FCS-5202 Gemini 4 MP Fixed IP Camera, showing the lens, IR LEDs, and mounting bracket.
3. Configuración e instalación
3.1 Precaucións de seguridade
- Asegúrese de desconectar a alimentación antes da instalación ou mantemento.
- Install the camera in a location that provides optimal viewing and is protected from direct impact.
- Use appropriate tools and follow local electrical codes.
3.2 Instalación física
- Escolla un lugar de montaxe: Select a suitable outdoor location, preferably under an overhang, that offers a clear field of view and is within reach of a network cable with PoE.
- Montar o soporte: Use the provided mounting accessories to securely attach the wall mount bracket to the chosen surface. Mark and drill pilot holes as necessary.
- Engade a cámara: Secure the camera to the mounting bracket. Adjust the camera's angle and orientation for the desired coverage.
3.3 Conexión de rede e alimentación
- Conectar o cable Ethernet: Connect a Cat.5 or higher Ethernet cable from your PoE-enabled switch or PoE injector to the camera's Ethernet port. This single cable will provide both power and data.
- Encendido: Once the Ethernet cable is connected to a PoE source, the camera will power on automatically. Allow a few minutes for the camera to boot up.
3.4 Configuración inicial
- Descubra a cámara: Use the LevelOne IP Camera Finder tool (available on the LevelOne website) or a network scanner to locate the camera's IP address on your network.
- Acceso Web Interface: Abrir a web browser and enter the camera's IP address. You will be prompted to enter a username and password. Refer to the default credentials provided in the camera's packaging or on the manufacturer's websitio.
- Cambiar as credenciais predeterminadas: For security purposes, immediately change the default username and password to strong, unique credentials.
- Configuración de rede: Configure network settings such as static IP address (recommended for surveillance devices), subnet mask, gateway, and DNS servers as per your network requirements.
- Data e hora: Set the correct date and time, preferably by synchronizing with an NTP server.
4. Instrucións de funcionamento
4.1 En directo View
Despois de iniciar sesión na cámara web interface, navegue ata "En directo View" section to see the real-time video feed from the camera. You can typically adjust stream quality and view options here.
4.2 Gravación de vídeo
- Gravación continua: Configure the camera to record video continuously to a Network Video Recorder (NVR) or network-attached storage (NAS).
- Event-Triggered Recording: Set up recording to activate only when specific events occur, such as motion detection.
- Gravación programada: Define specific time periods for recording.
4.3 Motion Detection and Event Management
- Configurar as zonas de detección: In the camera's settings, define specific areas within the camera's view onde a detección de movemento debería estar activa.
- Configuración de sensibilidade: Adjust the sensitivity of motion detection to minimize false alarms.
- Accións do evento: Specify actions to be taken when an event is detected, such as:
- Sending email notifications.
- Uploading recorded video clips to an FTP server.
- Triggering an alarm output (if available).
4.4 Acceso remoto
To access your camera remotely, you may need to configure port forwarding on your router or use a cloud-based service provided by LevelOne or a third-party NVR. Consult your router's manual or network administrator for port forwarding instructions.
5. Mantemento
5.1 Limpeza da cámara
- Limpe regularmente a lente e a carcasa da cámara cun pano suave eamp cloth to remove dust, dirt, and water spots.
- Do not use harsh chemicals or abrasive cleaners, as these can damage the lens or casing.
- Asegúrate de que a cámara estea apagada antes de limpala.
5.2 Actualizacións de firmware
Periodically check the LevelOne official website for firmware updates. Firmware updates can provide new features, improve performance, and enhance security. Follow the instructions provided with the firmware update package carefully.
6 Solución de problemas
| Problema | Causa posible | Solución |
|---|---|---|
| A cámara non se acende. | No power from PoE switch/injector; faulty Ethernet cable. | Verify PoE source is active. Check Ethernet cable connection and integrity. Try a different PoE port or cable. |
| Non se pode acceder á cámara a través de web navegador. | Enderezo IP incorrecto; problema de conectividade de rede; acceso bloqueado polo cortafuegos. | Confirm camera's IP address using discovery tool. Check network cable. Disable local firewall temporarily or add exception. Ensure camera and computer are on the same network segment. |
| Mala calidade de imaxe. | Dirty lens; improper focus (if adjustable); low light conditions; network bandwidth issues. | Clean the lens. Check camera settings for resolution and quality. Ensure adequate lighting. Verify network bandwidth is sufficient for video streaming. |
| A detección de movemento non funciona ou hai demasiadas falsas alarmas. | Incorrect sensitivity settings; detection zones not configured properly; environmental factors (e.g., moving branches). | Adjust motion detection sensitivity. Refine detection zones to exclude irrelevant areas. Consider environmental factors. |
7. Especificacións
| Característica | Detalle |
|---|---|
| Número de modelo | FCS-5202 |
| Resolución | 4 megapíxeles |
| Compresión de vídeo | H.264, H.265, MJPEG |
| Conectividade | Wired (802.3af Power over Ethernet - PoE) |
| Fonte de enerxía | 802.3af PoE or 12V DC (Power adapter not included) |
| Consumo de enerxía | 5.76 vatios |
| Material | Metal |
| Ambiente de uso | Ao aire libre |
| Resistencia á intemperie | Clasificación IP67 |
| Dimensións (L x W x H) | 6.05 x 15.4 x 7 cm (2.38 x 6.06 x 2.76 polgadas) |
| Peso | 640 gramos (1.41 libras) |
| Tipo de montaxe | Soporte de montaxe en parede |
| Uso recomendado | Motion detection, Outdoor surveillance |
8. Garantía e soporte
For warranty information, please refer to the documentation provided with your purchase or contact your reseller. LevelOne provides technical support for its products. For assistance, please visit the official LevelOne websitio ou póñase en contacto co seu departamento de atención ao cliente.
Recursos en liña:
- LevelOne Official Websitio: www.level1.com
- Páxina de asistencia do produto: Busca FCS-5202 on the LevelOne website for drivers, firmware, and FAQs.
