Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Acabadoview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power amplifier, de baixo ruído amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Características

Funcións Wi-Fi

• Supports IEEE 802.11 b/g/n/ax
• Admite MAC completo, incluíndo LMAC e UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Soporta Mid-amble
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

Característica BLE

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Admite o envío e recepción de datos asíncronos
• Supports connection parameter update
• Supports extensible data packet length
• Admite o cifrado da capa de ligazón
• Soporta LE ping

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Especificación xeral

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Lista de materiais

Características eléctricas

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

Referido ao estándar IPC/JEDEC.

• Temperatura máxima: <250 °C
• Número de veces: ≤2 veces

package figure

Instrucións de embalaxe

1. 700 pzas

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Certificación
Instrucións de integración para fabricantes de produtos anfitrións segundo KDB 996369 D03 OEM Manual v01r01

Lista de normas FCC aplicables
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Condicións específicas de uso operativo
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampdeterminadas configuracións de portátiles ou co-ubicación con outro transmisor), entón a autorización da FCC xa non se considera válida e o ID da FCC non se pode utilizar no produto final. Nestas circunstancias, o integrador OEM será o responsable de reavaliar o produto final (incluído o transmisor) e de obter unha autorización separada da FCC.

Procedementos de módulo limitado
Non aplicable

Deseños de antenas de traza
Non aplicable

Consideracións sobre a exposición a RF
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Tipo de antena e ganancia

• As seguintes antenas foron certificadas para o seu uso con este módulo.
• Con este módulo só se poden utilizar antenas do mesmo tipo con ganancia igual ou inferior.
• Outros tipos de antenas e/ou antenas de maior ganancia poden requirir autorización adicional para o seu funcionamento.

Información de cumprimento da etiquetaxe do produto final
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Información sobre os modos de proba e os requisitos adicionais de proba
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Probas adicionais, Parte 15 Subparte B Exención de responsabilidade
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Información manual para o usuario final
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Como facer cambios - Nota importante
Se non se poden cumprir estas condicións (p. examp(por exemplo, certas configuracións de portátiles ou colocalización con outro transmisor), a autorización da FCC xa non se considera válida e o ID da FCC non se pode usar no produto final. Nestas circunstancias, o integrador OEM será responsable de reavaliar o produto final (incluído o transmisor) e obter unha autorización da FCC por separado.

Declaración da FCC

Este dispositivo está pensado só para integradores OEM nas seguintes condicións

1. The antenna must be installed such that 20 cm is maintained between the antenna and the user.
2. O módulo transmisor non pode estar situado con ningún outro transmisor ou antena.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Este dispositivo cumpre coa Parte 15 das normas da FCC. O funcionamento está suxeito ás dúas condicións seguintes:

1. Este dispositivo pode non causar interferencias daniñas.
2. Este dispositivo debe aceptar calquera interferencia recibida, incluídas as que poidan causar un funcionamento non desexado.

Nota: O beneficiario non se fai responsable dos cambios ou modificacións non aprobados expresamente polo responsable do cumprimento. Tales modificacións poderían anular a autoridade do usuario para operar o equipo.

NOTA: Este equipo foi probado e comprobouse que cumpre cos límites para un dispositivo dixital de Clase B, segundo a parte 15 das normas da FCC. Estes límites están deseñados para proporcionar unha protección razoable contra interferencias daniñas nunha instalación residencial. Este equipo xera usos e pode irradiar enerxía de radiofrecuencia e, se non se instala e usa de acordo coas instrucións, pode causar interferencias prexudiciais nas comunicacións por radio. Non obstante, non hai garantía de que non se produzan interferencias nunha determinada instalación. Se este equipo causa interferencias daniñas na recepción de radio ou televisión, o que se pode determinar acendendo e apagando o equipo, recoméndase ao usuario que intente corrixir a interferencia mediante unha ou máis das seguintes medidas:

• Reorienta ou reubica a antena receptora.
• Aumentar a separación entre o equipo e o receptor.
• Conecte o equipo a unha toma dun circuíto diferente ao que está conectado o receptor.
• Consulte ao distribuidor ou a un técnico experimentado de radio/TV para obter axuda.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

Declaración de exposición a RF
Este equipo cumpre cos límites de exposición á radiación da FCC establecidos para un ambiente non controlado. Este equipo debe instalarse e operarse cunha distancia mínima de 20 cm entre o radiador e o seu corpo