RTX 8930 Wireless Dect Headset
REMATADOVIEW
This manual explains how to operate the RTX SME VoIP DECT Headset (RTX8930) in generic mode, including power on/off, registration, basic call handling, volume control, and microphone muting.
Especificacións
- Modelo: RTX8930 headset
- Control de volume: Six volume steps (beeps indicate adjustments and limits)
- LED behavior (power/registration status): Blue LED blinks fast during initial signal detection/registration mode; after subscription it blinks with a 2-second interval
- Power-off key combination: Long-press AUX + VOL+ + VOL- for five seconds
Quick Setup & Use
- Activar: Preme o AUX key. Wait for the blue LED to blink fast until a signal is detected; once subscribed, the voice prompt “Headset subscribed” plays and the blue LED changes to a 2-second interval.
- Initial registration: For first-time setup, switch the headset on; it enters registration mode automatically (blue LED blinking fast).
- Subsequent (re-)registration: Mantén premido HOOK OFF xunto con VOL+ e VOL- until the blue LED starts blinking fast. (Note: the blue LED will not enter registration mode if the unit is cradled and charging.)
- Responde unha chamada: Preme HOOK OFF.
- Finalizar unha chamada: Preme HOOK OFF de novo.
- Adjust volume during a call: Preme VOL+ para aumentar e VOL- para diminuír.
- Silenciar/activar o micrófono: Preme MUTO to toggle mute on and off.Headset Operations Manual
Sobre este documento
This document describes the features and functionalities available in the RTX SME VoIP DECT Headset. We describe how to operate the headset without going into details about its mechanical features. The reference for features and operation in this manual is RTX generic mode.
PúblicoEsta guía está destinada tanto a usuarios cotiáns como a administradores de sistemas.
AbreviaturasPara os efectos deste documento, enténdese as seguintes abreviaturas:
- DECT: Telecomunicacións sen fíos melloradas dixitais
- IPEI: Identidade internacional de equipos portátiles
- MAC: Control de acceso a medios
- PBX: Intercambio de sucursales privadas
Referencias/Documentacións relacionadas
- [1]: How_To_Deploy_SME_Network_V1.3
- [2]: SME VoIP System Guide, Version 2.5
Historial do documento
| Revisión | Autor | Data de emisión | Comentarios |
|---|---|---|---|
| 0.1 | TMS | 26-Xul-2016 | Versión inicial. |
Marca comercial
| Nome do cliente | RTX | Wildix | SNOM | Strongbyte |
|---|---|---|---|---|
| Modelo No. | RTX8930headset | WAIR-Headset | A190 | VCV2840 headset |
| HVIN | 8930V10 | WAIRV10 | 190V10 | 2840V10 |
| Marca comercial |
Operación básica
This section describes how to switch on and off the RTX8930 headset and how to register the unit on an RTX 8660 SME VoIP system.
How to Switch the Headset On/Off:
Apagando os auricularesTo switch the headset off, long-press the AUX clave xunto co VOL+ e VOL- keys (press and hold the three keys for five seconds). The blue LED will give a short blink before switching off.
Registration Initial Registration
Inscricións posterioresIf the RTX8930 headset has already been registered on the same or another base system and needs to be re-registered, the required action is to press and hold the HOOK OFF clave xunto co VOL+ e VOL- keys until the blue LED starts blinking fast.
NOTA: The blue LED will not start blinking in registration mode if the unit is cradled and charging. Please check the additional document via [2] for more information about terminal registration on a base system.
Operacións de chamadas
- Chamada entrante As the headset receives an incoming call, a ringtone will be played back
- Respondendo a unha chamada entrante Para responder a unha chamada entrante, prema o HOOK OFF chave
- Rexeitar unha chamada entrante It is not currently possible to reject an incoming call
- Finalizando unha chamada To end an ongoing call, press the HOOK OFF chave
- Volume e silencio It is possible to adjust the earpiece volume up or down during calls by pressing the VOL+ e VOL- keys, respectively. There are six volume steps. A beep is played back to indicate that the volume is adjusted. A higher frequency beep is played back when the volume cannot be adjusted further up or down.
- Silenciar o micrófono It is possible to mute the microphone during calls by pressing the MUTO key. The microphone is unmuted by pressing the MUTO key again. A voice prompt announcing “Mute on” is played back when mute is activated. A voice prompt announcing “Mute off” is played back when mute is deactivated.
Resolución de problemas
- Headset doesn’t enter registration mode when re-registering: If you are cradled and charging, the blue LED will not start blinking fast in registration mode. Remove it from the cradle/charging and try again.
- No confirmation after switching on: Despois de presionar AUX, the blue LED should blink fast until a signal is detected. Once the headset locks onto a base, the voice prompt “Headset subscribed” should play and the LED should switch to blinking with a 2-second interval.
- Volume can’t be increased/decreased: The headset provides higher frequency beeps when the volume cannot be adjusted further up or down.
Documentos/Recursos
 | 8930 Wireless Dect Headset |
Referencias
- Manual de usuariomanual.tools