Manual de instrucións da luz lineal Aria de stem

Stem Aria Linear Light

PRECAUCIÓN

ANTES DA INSTALACIÓN

Please read the provided step-by-step instructions thoroughly before proceeding with the installation. You will achieve a secure and successful installation by taking these precautions and diligently following the provided guidelines.

1. Lembra sempre desconectar a alimentación do circuíto antes de comezar calquera traballo de instalación. As tarefas de instalación eléctrica deben ser realizadas exclusivamente por un contratista eléctrico autorizado. Para obter orientación profesional, póñase en contacto coa súa autoridade eléctrica local.
2. Antes da instalación, verifique na zona de instalación a presenza de outros cables para evitar danos no cableado oculto.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light up to 3kg ( 6.6 lbs, aluminium)/ 7kg (15.4 lbs, brass).
4. Teña en conta que este dispositivo está deseñado só para o seu uso en ambientes interiores domésticos secos.
5. When handling the metal fixture, make sure your hands are clean. It is advised to wear gloves to prevent leaving marks on the metal surface.
6. Periodically check screws and connections for stability. Gently tighten if necessary, avoid over-tightening.

INSTRUCIÓNS DE COIDADO

Asegúrese de que as mans estean limpas antes de tocar a superficie metálica para non deixar marcas de pegadas dixitais. Recoméndase o uso de luvas ao manipular o dispositivo de iluminación. Non use substancias abrasivas no produto. Teña coidado co seu peso. Manexa con coidado.

Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface.

DATOS TÉCNICOS

• Dimensións
  • Dia.. 26 L1440 MM
  • Dia 1 L56.7 IN (Custom length on request)
• Material e peso
  • Cast Aluminium – 2.5 kg
  • Cast Brass – 6 kg
• Clasificación Kelvin 3000K
• Fonte de luz
  IND/ UK/ EU LED strip (Incl.)12W, 220-240V
• Classification IP20
• Corte de fase regulable, compatible con TRIAC
• Hardware
  W56 H32 D140 MM W2.2 H1.3 D5.5 IN Aluminium, Brass finish
• Cordón
  • Hardwire
  • Cord length – 2000 MM

DENTRO DA CAIXA

* Driver and LED light are not included for regions with a voltagRequisito de 110-120 V.

(Fig. 1)

PASO 1

Position and drill

Carefully mark the position where you intend for the light fixture to hang. Use the dimensions marked (Fig. 1) as a guide to drill holes in the ceiling, then proceed to the next step.

(Fig. 2)

PASO 2

Install the Clutch wire gripper and Canopy back plate

1. Connect the clutch wire gripper (A1) and canopy back plate (B) by fastening them at the drilled holes in the ceiling using the drywall screws (Fig. 3).
2. Insert the clutch wire (C) through the clutch wire screw (D)(Fig. 4), fitted on the ends of the cast Rod.
3. Secure the opposite end of the clutch wire gripper (A1)(Fig. 3).
   1. To ensure the safe suspension of the light fixture, check that the wires are firmly attached to the clutch wire grippers and are devoid of any slack.

(Fig. 5)

PASO 3

Install the second Clutch wire gripper

Take the second clutch wire gripper (A2) and fasten it directly onto the ceiling (Fig. 6) using the drywall screw. Now insert the clutch wire (C) through the clutch wire screw (D) (Fig. 4) and securely attach it to the clutch wire gripper (A2) (Fig. 6).

(Fig. 7)

PASO 4

Install and level the Rod

Fasten the clutch wire screw (D) to both ends of the Rod (Fig. 7) and adjust its height as desired. Ensure that the light fixture is in alignment with the floor.

(Fig. 8)

PASO 5

Connect the wiring to the driver

1. Insert the LED cord end (F) on the Rod through the hole in the canopy casing (E) and connect it to the driver output mounted on the ceiling (Fig. 8).
2. Connect the driver input to the electrical connection in the ceiling (Fig. 9).
   Ensure that all connections are secure and that there are no exposed wires or electrical hazards. Pay attention to the polarity of the connection. A wrong connection can cause damage.

(Fig. 10)

PASO 6

Close the Canopy casing

After completing the installation, take the canopy’s top cover and attach it to the back plate (Fig. 10) using the canopy screws (Fig. 11). Ensure that the wiring and any excess clutch wire strands are neatly trimmed after the installation.

In case you require further assistance, please write to us at info@stemdesign.co.

Preguntas frecuentes