THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Guía de inicio rápido

Contido do paquete

Especificacións

Restablecemento de fábrica

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Escanee o código QR para view detalles

https://bit.ly/488mkj9

Resolución de problemas

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. O dispositivo non se acenderá
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

Conformidade normativa da FCC
Este dispositivo cumpre coa parte 15 das normas da FCC. O funcionamento está suxeito ás dúas condicións seguintes: (1) Este dispositivo non pode causar interferencias prexudiciais e (2) este dispositivo debe aceptar calquera interferencia recibida, incluídas as que poidan causar un funcionamento non desexado.
Calquera cambio ou modificación non aprobado expresamente pola parte responsable do cumprimento pode anular a autoridade do usuario para operar o equipo.
Nota: Este equipo foi probado e comprobouse que cumpre cos límites para un dispositivo dixital de Clase B, segundo a parte 15 das normas da FCC.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorientar ou reubicar a antena receptora.
– Aumentar a separación entre o equipo e o receptor.
– Conecte o equipo a unha toma de corrente dun circuíto diferente ao que está conectado o receptor.
– Consulte ao distribuidor ou a un técnico experimentado de radio/TV para obter axuda.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Para obter unha garantía limitada, visite
https://thirdreality.com/faq-help-center/
Para atención ao cliente, póñase en contacto connosco en
info@3reality.com ou visitar www.thirdreality.com
For questions on other platforms, visit the corresponding
platform’s application/support platform.