XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

Conexión por cable

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Precaucións para o diagnóstico

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

Escanee o código QR ou visite
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
Descomprimir o descargado file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

Como usar
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

Marcas comerciais
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Exención de garantías e limitación de responsabilidade
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

Soporte e Servizo

Oficial Websitio: www.xtooltech.com
Correo electrónico: xtoolinplusus@outlook.com

Introdución xeral

Outlook e portos

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

Cor da luz indicadora	Indicador luminoso Significado
Luz verde continua	Encendido
Luz verde intermitente	Actualización de firmware
Luz azul sólida	Device connected (no communication)
Luz azul intermitente	Communicating with the vehicle
Luz vermella intermitente	Avaría do dispositivo

Comezando

Conexión do vehículo

Conexión sen fíos

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

Conexión por cable

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Precaucións para o diagnóstico

O voltage rango no coche: +9~+36V DC;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
Os sistemas de control electrónico dos diferentes modelos son moi complicados. Se atopa situacións nas que é imposible probar ou unha gran cantidade de datos de proba é anormal, pode buscar a ECU do vehículo e seleccionar o menú para o modelo na placa de identificación da ECU;
Só se permiten utilizar con este dispositivo arneses de cableado proporcionados por XTOOL e deseñados para o dispositivo para evitar danos ao vehículo ou ao dispositivo;
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

Instalación

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

Como usar

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

Pantalla principal
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

Configuración

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

Comentarios

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

O teu enderezo de correo electrónico
Rexistro files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

Conformidade FCC

FCC ID: 2AW3IV01W2

Este dispositivo cumpre coa Parte 15 das normas da FCC. O funcionamento está suxeito ás dúas condicións seguintes:

Este dispositivo pode non causar interferencias daniñas
Este dispositivo debe aceptar calquera interferencia recibida, incluídas as que poidan causar un funcionamento non desexado.

Aviso
Os cambios ou modificacións non aprobados expresamente pola parte responsable do cumprimento poden anular a autoridade do usuario para utilizar o equipo.

Nota
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorienta ou reubica a antena receptora.
Aumentar a separación entre o equipo e o receptor.
Conecte o equipo a unha toma dun circuíto diferente ao que está conectado o receptor.
Consulte ao distribuidor ou a un técnico experimentado de radio/TV para obter axuda.

Parte Responsable

Nome da empresa: FCC US Agent, LLC
Enderezo: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
Correo electrónico: Soporte@FCCUSAgent.com

Declaración ISED

IC: 29441-V01W2
Model: XTS500
PMN: V120，XTS500
HVIN: V01W2A

Este dispositivo contén transmisores/receptores exentos de licenza que cumpren os RSS exentos de licenza de Innovation, Science and Economic Development Canada. O funcionamento está suxeito ás dúas condicións seguintes:

Este dispositivo pode non causar interferencias.
Este dispositivo debe aceptar calquera interferencia, incluídas as que poidan causar un funcionamento non desexado do dispositivo.

Declaración de conformidade
Por medio da presente, Shenzhen XTOOLtech Intelligent Co., Ltd declara que este módulo de diagnóstico sen fíos cumpre cos requisitos esenciais e outras disposicións pertinentes da Directiva 2014/53/UE. De acordo co artigo 10(2) e o artigo 10(10), este produto pode ser utilizado en todos os estados membros da UE.

UKCA

Por medio da presente, Shenzhen XTOOLtech Intelligent Co., Ltd declara que este módulo de diagnóstico sen fíos cumpre todas as normativas técnicas aplicables ao produto dentro do ámbito do Regulamento de equipos de radio do Reino Unido (SI 2017/1206); o Regulamento de equipos eléctricos (seguridade) do Reino Unido (SI 2016/1101); e o Regulamento de compatibilidade electromagnética do Reino Unido (SI 2016/1091) e declara que a mesma solicitude non se presentou ante ningún outro organismo aprobado polo Reino Unido.
Shenzhen Xtooltech Intelligent Co., Ltd.
Engadir: 17&18/F, edificio A2, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China
Teléfono da sede central de Shenzhen: +86 755 2399608
Correo electrónico: marketing@xtooltech.com

Preguntas frecuentes

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

Documentos/Recursos

XTOOL XTS500 Wireless Diagnostics Module [pdfManual do usuario
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

Referencias

Manual de usuario

XTOOL XTS500 Wireless Diagnostics Module

Especificacións

Instrucións de uso do produto